Flange Adapters (MS-02-200;rev J;en-US;Catalog) - Swagelok
ANSI Flanges with Swagelok Tube Fitting or Tube Adapter Ordering Information and Dimensions Dimensions are for reference only and are subject to change. D H A E J B F, flat Pressure-Temperature Ratings Ratings are taken from ASME B16.5, Table 2-2.2 and Table II-2-2.2 (based on A182 316 stainless steel material).
Download Flange Adapters (MS-02-200;rev J;en-US;Catalog) - Swagelok
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
23 22 13 Steam and Steam Condensate Piping (072913)
www.uh.edu3. Each fitting shall be stamped as specified by ANSI B31.9. G. Flanges: 1. All 150 lb. and 300 lb. ANSI flanges shall be weld neck and shall be domestically manufactured, forged carbon steel, conforming to ANSI B16.5 and ASTM A1-191 Grade I or II or A-105 as made by Tube Turn, Hackney or Ladish Company. Slip on flanges shall not be used.
Lap Joint Stub Ends - ANSI B16 - Pipe Fittings & Flanges ...
www.metline-pipefittings.in- Dimension B conforms to ASME/ANSI B16.5, Pipe Flanges and Forged Fittings. - Gasket face finish shall be accordance with ASME/ANSI B16.5 for raised face flanges. - For tolerances see page 6-2. 1 Long pattern weights are listed (short pattern weights are similar to MSS SP-43 lap joint stub ends, page 6-20).
Double Block and Bleed with Ultra-Low Emission options
www.parker.com• 1/2” to 2” N.B. Flanges (15 to 50 DN) • ANSI B16.5 150 to 2500 flange class and API 10,000 • 1/2-14 NPT (female) standard outlet • 1/4-18 NPT (female) standard vent • Variety of optional end connection sizes and thread forms including tube connections 1/2”/12mm diameter • Standard materials of construction: Stainless