Generator G11 (GEN11)
Standard Conventions Used The Use of WARNING, Caution, and Note Statements ... A Warning statement indicates an operating or maintenance procedure, practice, or condition that, ... • Do not operate the unit in close proximity to volatile solvents such as methanol or alcohol as combustion may occur ...
Download Generator G11 (GEN11)
Information
Domain:
Source:
Link to this page:
Related documents
Validation and Calibration of Analytical Instruments
jbsr.pharmainfo.inWater: Methanol (70:30v/v) Injector Accuracy: 1. Connect the pump and detector inlet with union. 2. Prepare mobile phase consisting of a mixture of water and Methanol (70:30 v/v) 3. Set a flow rate of 0.5 ml/m and a run time of 1 m. 4. Set the column temperature at 25± 2°C. 5. Fill a standard HPLC vial to 2/3rd with Milli-Q water.
A09-009A Determination of Aspirin Using UV and Visible …
www.jenway.comStandard Preparation:- A stock standard equivalent to 25mg/l aspirin was prepared by dissolving 19.2mg of salicylic acid and 0.1g of citric acid in a minimum amount of purified water. This solution was diluted to 100.0ml with methanol. Working standards were prepared by pipetting 5, 10 and 20 ml aliquots of the stock standard solution into separate
Soil Sampling Standard Operating Procedure: August 1997 ...
archive.epa.govcleaned in the field using standard decontamination procedures as outlined in E & E’s Standard Operating Procedure (SOP) for Sampling Equipment Decontamination (see ENV 3.15). 4. Sample Preservation, Containers, Handling, and Storage The chemical preservation of solids is not generally recommended. Refrigeration is usu
Sodium Hypochlorite (Bleach) Safety Fact sheet
ehs.stanford.eduResponse Standard Operating Procedure (SOP). For larger spills, call EH&S at 650-725-9999. For health emergencies, call 911 (9-911 from a campus phone). References Bretherick's handbook of reactive chemical hazards Stanford University B iosafety Manual Stanford University H andling Mixed Waste
POLYETHYLENE GLYCOLS
www.fao.orgProcedure Place 50 ml of anhydrous methanol into a 250-ml conical flask. Add 4 to 6 drops of Mixed indicator, and titrate with Standard methanolic hydrochloric acid to a clear blue colour. Transfer to the flask about 25 g of the sample, accurately weighed, to provide the specimen blank, swirl to effect complete solution. Titrate with
Acrylonitrile - Ineos
www.ineos.comof equipment and operating conditions. (For example, “nitrogen blanketing” – a procedure designed to prevent flammable vapor mixtures during handling, transfer and storage of Acrylonitrile. See Section 3.) Solubility Acrylonitrile is miscible with most organic solvents, includ-ing acetone, acetonitrile, benzene, carbon tetrachloride,
Controlling Contamination in LC/MS
www.waters.comCONTROLLING CONTAMINATION IN LC/MS SYSTEMS 715001307 REV.. G 4 OF 33 Use ultra‐pure water Use ultra‐pure water (defined as water that has been purified through a system that targets contaminants detrimental to UPLC®/MS and HPLC/MS systems). Note: See Recommended water purification process, page 29. Ultra‐pure water is sterile and contains no …
ACQUITY UPLC and ACQUITY PREMIER HSS Columns
www.waters.comThe flow rates given in the procedure below are for 2.1 mm I.D. columns. 1. Purge the pumping system of any buffer-containing mobile phases and connect the inlet end of the column to the injector outlet. 2. Flush column with 100% organic mobile phase (methanol or acetonitrile) by setting the pump flow rate to 0.1 mL/min