High-Flow, Springless Diaphragm Valves
DF SERIES DIAPHRAGM BALL PLUG VALVES NEEDLE METERING VALVES CHECK RELIEF VALVES REGULATORS & FILTERS INSTRUMENT MANIFOLD MEASUREMENT DEVICES REFERENCES MEDIUM- HIGH- PRESSURE Panel Mounting Is available for round-handle valves. Includes threaded bonnet nut and 1/8 in. hex panel mount nut. Requires 0.96 in. (24.4 …
Download High-Flow, Springless Diaphragm Valves
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
COUNTERBALANCE VALVES - Bosch Rexroth
apps.boschrexroth.comthe relief opening and the piloted opening are independent from back-pressure at port V2. Venting is often open to atmosphere and, whenever possible, is connected to tank or to a low pressure line. They must be used only in conjunction with main control valves having closed centre spools and equipped with port relief valves.
safety and relief valve catalog
www.bayportvalve.comSafety Relief Valves 5 10-408 10-418 10-214 10 Series Brass/bronze safety relief valves protect ASME Section IV hot water heating boilers and hydronic heating systems. High capacity design features corrosion resistant construction. Brass, satin or polished chrome finishes available. ASME Section IV Sizes 3/4" - 1" Set Pressure 20-150 psi
CROSBY J-SERIES DIRECT SPRING PRESSURE RELIEF VALVES
www.flotechinc.comDIRECT SPRING PRESSURE RELIEF VALVES SEAT DESIGN Series JOS-E and JBS-E relief valves are available with flat metal-to-metal or soft seats. Their two-piece disc holder/disc insert construction provides thermal balancing assuring maximum seat tightness and meets the requirements of API Standard 527, ‘Seat tightness of pressure relief valves’.
Trunnion-mounted Ball Valves
www.lntvalves.comL&T Trunnion-mounted Ball Valves are also offered with Double Piston seats. In this design, cavity pressure acts on both upstream and downstream seats to create a ‘double piston’ effect on seat rings that enhances sealing. Valves with Double Piston seats require an external cavity relief mechanism while handling non-compressible fluids.
PRESSURE RELIEF VALVES
www.rathvac.comwithin 10% over set pressure. After discharge Pressure Relief Valves will blow down and reseat once the pressure falls below the valves set pressure. Materials of Construction The 52 series Relief Valves have brass valve bodies. The internal parts are made of brass and carbon steel. The 53 series valves have stainless steel valve bodies.
Proportional Relief Valves - Swagelok
www.swagelok.com2 Check Valves and Relief Valves R SERIES Features High-Pressure Valves Service up to 6000 psig (413 bar) Multiple springs for a selection of set pressure ranges Valves available factory-set to a specified set pressure 1/4 in. and 6 and 8 mm end connections—R3A series 1/2 in. and 12 mm end connections—R4 series Low-Pressure Valves