High-Performance, High-Movement, Single-Component ...
High-Performance, High Movement, Single-Component, Polyurethane Sealant www.tremcosealants.com Page 2 of 3 Tremco recommends that surface temperatures be 40 ˚F (5 ˚C) or above at the time the sealant is applied. If sealant must be applied in temperatures below 40 ˚F, please refer to the Tremco Technical Bulletin
Download High-Performance, High-Movement, Single-Component ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
TREMDrain® DPI - Tremco Sealants
www.tremcosealants.comTREMDrain® DPI Drainage and Protection Board Product Description TREMDrain® DPI is an optional drainage, protection and insulation board designed for use primarily with TREMproof® 260 Spray-Applied
SAFETY DATA SHEET - Tremco Sealants
www.tremcosealants.comSAFETY DATA SHEET 1. Identification ... Do not handle until all safety ... Total dust. PEL 15 mg/m3 US.
Tremco® 440 Tape - Tremco Sealants
www.tremcosealants.comTremco® 440 Tape Butyl Sealant Tape www.tremcosealants.com Page 1 of 2 Product Description Tremco® 440 Tape is a 100% solid polyisobutylene cross-linked butyl, preformed sealant.
TREMstop® Acrylic - Tremco Sealants
www.tremcosealants.comTREMstop® Acrylic An Acrylic Latex Firestop Sealant Page www.tremcosealants.com 1 of 4 Product Description • TREMstop® Acrylic is a gunnable acrylic latex sealant designed for use in
System No. C-AJ-7044 - Tremco Sealants
www.tremcosealants.comReprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc. Copyright © 2008 Underwriters Laboratories Inc. ®
Technical Service Bulletin - Tremco Sealants
www.tremcosealants.comIntegrated Technical Solutions . Technical Service Bulletin . Tremco ExoAir air barrier membrane gap bridging and joint movement considerations . The purpose of this bulletin is to assist design professionals and contractors in selecting the best materials
Proglaze® - Tremco Sealants
www.tremcosealants.comProglaze® Single-Component, Moisture-Cure, Acetoxy Silicone Sealant for Glazing Page www.tremcosealants.com 1 of 2 Product Description Proglaze® is a single-component, moisture-cure, acetoxy, silicone sealant for
Spectrem® 2 - Tremco Sealants
www.tremcosealants.comSpectrem® 2 Single-Component, Neutral-Cure Silicone Sealant for 2-Sided Structural Glazing Page www.tremcosealants.com 1 of 3 Product Description Spectrem® 2 is a high-performance, single-component, neutral-cure,
SEALANT SELECTION GUIDE
www.tremcosealants.comThe Sealant Selection Guide should only be used as a guide. Reference the Data Sheet for more specific information and/or consult your local Tremco Representative or Technical Services. * Modified ASTM C719 ** Willseal 600 can be used in non-immersed applications where there is no ponding water and as a backer rod on horizontal joints.
Single-Component, Rapid Curing, Fluid-Applied Elastomeric ...
www.tremcosealants.comSINGLE LIFT SYSTEM TREMproof 250GC may be applied in a single pass up to 120 mils for horizontal applications. Apply at a rate of 13 ft²/gal (0.32 M²/L.) 6.3 Multi-lift 215-mil system Apply the first coat of TREMproof 250GC at a rate of 18 ft²/gal (0.44 M²/L), to yield 90 mils. Allow the TREMproof 250GC to cure to a firm
Related documents
Understanding U-Factors
www.wausauwindow.comSingle-number rating systems can be misleading. A balanced design approach is strongly recommended. Energy efficient building designs must comply with codes, and meet owner expectations. Design professionals are increasingly concerned with misrepresentation of energy savings. Performance assessment must go beyond “R-Value.”
MS Polymers in “Hybrid” Sealants Edward M. Petrie “Hybrid ...
www.adhesives.orgSpecification TT-S-00230C Type II, Class A as a one-component sealant and Specification TT-S099227E Type II, Class A as a two-component sealant. MS sealants also meet ISO Standard 11600G, Class 25HM (high modulus). Table 4 compares the performance of silicone rubber, polyurethane, and MS sealants.
Vulkem® 45SSL - Tremco
www.tremcosealants.comSemi-Self-Leveling, Single-Component, Polyurethane Sealant www.tremcosealants.com Page 2 of 3 Sealant Dimensions W = Sealant width, D = Sealant depth, Expansion Joints- The minimum width and depth of any sealant application should be 1/4" x 1/4" (6 mm x 6 mm). The depth (D) of sealant may be equal to width (W) of joints that are less than 1/2 ...