High-Pressure, Pneumatically Actuated Bellows-Sealed …
PIPE, WELD, direction for system versatilityFITTINGS STANDARD TUBING ... 300SSTEMS MEASUREMENT DEVICES REFERENCES MEDIUM- HIGH- PRESSURE Inverted bellows design for strength Pressure-Temperature Ratings Valve Body Material 316 SS Stem Tip Material PCTFE Polyimide Temperature ... 2024-T4 aluminum/ B211 O-rings Fluorocarbon …
Download High-Pressure, Pneumatically Actuated Bellows-Sealed …
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
Flexmaster Joints - Eaton
www.eaton.comVAcUUM rATINGS † Size Range Standard Self-Restrained Pipe Tube Gasket Gasket All sizes All sizes 5 in. Hg. 5 in. Hg. 1.79 bar 1.79 bar NOTE: º F., inches, in. Hg., psi in bold º C., mm, bar, MPa in light PrESSUrE rATINGS † Size Range Standard Self-Restrained Pipe Tube Gasket 3/8 - 3/4 1/2 - 1 3/8 300 psi 300 psi
Enclosure Design - Saginaw Control
www.saginawcontrol.comconsists of at least three spray heads mounted in a water supply pipe rack. The enclosure is positioned in the focal area of the spray heads so that the greatest quantity of water is likely to enter the enclosure. The water pressure is maintained at 34.5kPa (5 psi) at each spray head and a continuous water spray shall be applied for one hour.
Metering Valves S, M. L, and 31 Series (MS-01-142;rev M;en ...
www.swagelok.comPressure-Temperature Ratings Orifice in. (mm) Shutoff Service Stem Taper (Included Angle) Temperature °F (°C) Working ... PIPE, WELD, VCR, VCO FITTINGS STANDARD TUBING MODULAR SYSTEMD HOSE / FLEXIBLE TUBING BELLOWS, DIAPHRAGM ... Green anodized aluminum 6061-T651/B211 Black oxide and light oil-coated alloy steel/ANSI 18.3
UTILITY SETS C F n - tcf.com
www.tcf.comThe ratings shown are based on tests and ... Static pressure to 2.5" w.g. BCV (Belt Driven) Backward inclined wheel 10.5" to 60" wheel diameters Airflow to 78,660 CFM ... pipe coupling is welded to the lowest point in the housing scroll to permit wash water or condensation