High-strength structural bolting assemblies for …
EN 14399-2:2005 (E) 3 Foreword This document (EN 14399-2:2005) has been prepared by Technical Committee CEN/TC 185, "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
Download High-strength structural bolting assemblies for …
Information
Domain:
Source:
Link to this page:
Documents from same domain
www.bsf-sh.com
www.bsf-sh.comICS 21.060.01; 25.220.40 Ref. No. ISO 10684:2004/Cor.1:2008(E) © ISO 2008 – All rights reserved Published in Switzerland INTERNATIONAL STANDARD ISO 10684:2004
Socket Cap, Set Screws, Hex and Spline Keys (Inch …
www.bsf-sh.comFOREWORD American National Standards Committee B18 for the standardization of bolts, screws, nuts, rivets, and similar fastenerswasorganizedinMarch1922asSectionalCom-
High-strength structural bolting assemblies for …
www.bsf-sh.comEUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 14399-1 March 2005 ICS 21.060.01 English version High-strength structural bolting assemblies for preloading - Part
Metric thread stud bolts 976-1 - bsf-sh.com
www.bsf-sh.comPage 3 DIN 976-1 : 2002-12 Table 1: Stud bolt dimensions Thread size (d)Nominal Approx. mass, in kg, per 1 000 units size Min. Max. (continued)
p160-206
www.bsf-sh.comICS 21.060.10 Studs with a length of engagement equal to about 1,25 d February 1995 DIN 939 Supersedes December 1972 edition. Descriptors: Fasteners, studs.
INTERNATIONAL ISO STANDARD 898-1
www.bsf-sh.com⎯ having thread tolerances in accordance with ISO 965-1, ISO 965-2 and ISO 965-4. It is not applicable to set screws and similar threaded fasteners not under tensile stress (see ISO 898-5). It does not specify requirements for such properties as
Related documents
MONTAGEWINKEL UND -SCHIENE
media.wuerth.comMWF - 09/11 - 14399 - © MONTAGEWINKEL UND -SCHIENE Bei Vorbohrung bis max. Ø 10,6 mm und ordnungsgemäßer Anbringung der Abdeck-kappen ist eine ausreichende ...
Lateral torsional buckling and slenderness
www.newsteelconstruction.com34 NSC October 2006 BS EN PUBLICATIONS The following are British Standard implementations of the English language versions of European Standards (ENs). BSI has an
PEINER High Strength Structural Bolts - Relay …
www.relayinternational.com.au2 | Page For the non hot-dip galvanised combinations, according to the new EN standard, the same tightening torques apply as for the hot-dip galvanised combinations, there where DIN 18800-7 (2002-09) Table 6,
CONSTRUCTION High strength Pre-Load Bolt …
www.srubena.comCONSTRUCTION High strength Pre-Load Bolt Assemblies HV and HR M12÷M36* Grade: HV - 10.9 HR - 8.8, 10.9 EN * M39÷M56 acc. to DASt- Richtlinie 021 EN DIN EN-14399-3 – Bolt and Nut Assemblies, type HR
STANDARD PRODUCTS - Tigges
www.tigges.com.mySTANDARD PRODUCTS FULL-CATALOGUE Tigges Fastener Technology (M) Sdn. Bhd. Lot 197067, Jalan Klebang 1/6 Zon Perdagangan Bebas …
SERVICE - chavesbao.com
www.chavesbao.comLíderes en tornillería Un liderazgo alcanzado desde el com-promiso en suministrar a nuestros clientes no sólo una amplia gama de producto y calidad excelente, sino