High-strength structural bolting assemblies for Licensed ...
EN 14399-1:2005 (E) 3 Foreword This document (EN 14399-1:2005) has been prepared by Technical Committee CEN/TC 185, "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
Download High-strength structural bolting assemblies for Licensed ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
www.bsf-sh.com
www.bsf-sh.comICS 21.060.01; 25.220.40 Ref. No. ISO 10684:2004/Cor.1:2008(E) © ISO 2008 – All rights reserved Published in Switzerland INTERNATIONAL STANDARD ISO 10684:2004
Socket Cap, Set Screws, Hex and Spline Keys (Inch …
www.bsf-sh.comFOREWORD American National Standards Committee B18 for the standardization of bolts, screws, nuts, rivets, and similar fastenerswasorganizedinMarch1922asSectionalCom-
High-strength structural bolting assemblies for …
www.bsf-sh.comEUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 14399-2 March 2005 ICS 21.060.01 English version High-strength structural bolting …
Metric thread stud bolts 976-1 - bsf-sh.com
www.bsf-sh.comPage 3 DIN 976-1 : 2002-12 Table 1: Stud bolt dimensions Thread size (d)Nominal Approx. mass, in kg, per 1 000 units size Min. Max. (continued)
p160-206
www.bsf-sh.comICS 21.060.10 Studs with a length of engagement equal to about 1,25 d February 1995 DIN 939 Supersedes December 1972 edition. Descriptors: Fasteners, studs.
INTERNATIONAL ISO STANDARD 898-1
www.bsf-sh.com⎯ having thread tolerances in accordance with ISO 965-1, ISO 965-2 and ISO 965-4. It is not applicable to set screws and similar threaded fasteners not under tensile stress (see ISO 898-5). It does not specify requirements for such properties as
Related documents
ÍNDICE DE EQUIVALENCIAS DIN – ISO
www.tornillera.com561 - 979 - 6914, 6915 en 14399-4 11023, 11024 - 562 - 980 7042 6916 en 14399-6 15237 - Índice de equivalencias iso – din iso din iso din iso din iso din 299 508 / 787 4034 555 7414 6915 10510 6901 773 6885 - 1, 2 4035 439 -2, 936 7416 6916 10511 985 774 6886, 6887 4036 439 ...
Geschraubte Verbindungen Tragfähigkeiten nach DIN EN …
bauforumstahl.deJan 08, 1993 · Groß DIN EN 14399-3; -4; -8 Gleitflächenklasse A (µµ = 0,5) Gleitwiderstände F s,Rd ,ser und s,Rd [kN] Kate- Gewinde gorie M Grenz-zustand M Festigkeits-klasse M12 M16 M20 M22 24 27 30 36 8.821 ,4 39,9 62,3 77,2 89,7 117 143 208 B Gebrauchs-
DIN EN 14399-4:2015-04 - Sahand Poulad
sahandpoulad.comDIN EN 14399-4:2015-04 2 A comma is used as the decimal marker. National foreword This document (EN 14399-4:2015) has been prepared by Technical Committee CEN/TC 185 “Fasteners” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Mechanische
Ausführung geschraubter Verbindungen nach DIN EN 1090-2
www.uni-due.deKennzeichnung – Schraubengarnituren nach DIN EN 14399-i e s ∅d 2 ∅d 1 Scheibe mit Fase DIN EN 14399-6 Mutter DIN EN 14399-4 Schraube DIN EN 14399-4 Scheibe DIN EN 14399-5 H XYZ XYZ 10.9 HV XYZ 10 HV XYZ H z. B. System HV Hersteller Hersteller Hersteller M36 - Garnitur