HILTI TECHNICAL BULLETIN
Mar 04, 2018 · Table 4 - Hilti HIT-HY 270 allowable tension and shear values for reinforcing bars based on steel strength 1,2,3 Rebar Size Tension, lb (kN) Shear, lb (kN) ASTM A615, Grade 60 ASTM A615, Grade 60 No. 3 3,270 1,685 (14.5) (7.5) No. 4 5,940 3,060 (26.4) (13.6) No. 5 9,205 4,745 (40.9) (21.1) No. 6 ...
Download HILTI TECHNICAL BULLETIN
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1/8 Safety Data Sheet acc. to ISO 11014 - Hilti USA
www.hilti.comPage 2/8 Safety Data Sheet acc. to ISO 11014 Printing date 05/19/2015 Version number 5 Reviewed on 05/19/2015 (Contd. of page 1) 40.2.7 H319 Causes serious eye irritation.
Hilti. Outperform. Outlast.
www.hilti.comSelector Guide Through-Penetration Joint Reference Data Firestop Mortar (CP 637) Product description ... Concrete and masonry assemblies Expansion on setting (approx.)Walls and floors rated up to 4 hours ... Mix ratio (recommended, mortar to water):
ICC-ES Evaluation Report ESR-2269 - Hilti
www.hilti.com1.0 EVALUATION SCOPE Compliance with the following codes: 2018, 2015, and 2012 International Building Code ® (IBC) 2018, 2015, and 2012 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2269 LABC and LARC Supplement.
HIT-RE 500 V3 - Hilti
www.hilti.comSafety information for 2-Component-products 18/06/2020 US-OSHA - en 2/27 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.
Hilti HIT-HY 200 with HIT-V
www.hilti.comAnchor rods HIT-V GR / -HCR) are available in variable length MIO M12 TE 16 M16 M20 M24 TE 40 M27 - TE 70 M30 compressed air gun or blow out pump, set of cleaning brushes, dispenser Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD Or TE-YD hollow drill bit with Hilti vacuum attachment. This drilling
Hilti HIT-HY 200 with rebar
www.hilti.comHilti HIT-HY 200 with rebar Benefits - suitable for cracked and non- cracked concrete C 20/25 to C 50/60. - Approved automatic cleaning with the use of the hollow drill-bit high loading capacity, excellent handling HY 200-R version with extended curing time for rebar applications small edge distance and anchor spacing possible
KB-TZ2 TECHNICAL GUIDE
www.hilti.comKB-TZ2 Technical uide April 2021 5 Table 4 - Allowable Hilti carbon steel KB-TZ2 strength in uncracked concrete for hammer drill and core drill installations 1,2,3,4 Nominal anchor
OPENINGS IN COMPOSITE FLOOR DECKS - Hilti
www.hilti.comin-situ reinforced concrete topping. The decking not only acts as a permanent formwork to the concrete, but also provides sufficient shear bond with the concrete so that, when the concrete has cured, the two materials act together compositely to resist the loads on the deck. Openings in floor decks are a common part of any building.
HIT-1 ADHESIVE ANCHORING SYSTEM - Hilti
www.hilti.comHIT-1 ADHESIVE ANCHORING SYSTEM Technical Supplement PRODUCT DESCRIPTION Hilti HIT-1 is a hybrid adhesive mortar combining resin, hardener, cement, and water. It’s formulated for fast curing and easy installation in a wide range of concrete and masonry base materials with temperatures ranging from 32°F (0°C) up to 95°F (35°C).
ICC-ES Evaluation Report ESR-4266
www.hilti.comDesign strength of anchors complying with the 2012 IBC as well as Section R301.1.3 of the 2012 IRC, must be determined in accordance with ACI 318-11 Appendix D and this report. Design parameters provided in Table 4, Table 5, Table 6 and Table 7 of this report are based on the 2021 IBC (ACI 318-19), 2018 and 2015 IBC (ACI 318-14) and the 2012 IBC
Related documents
Chapter 3 Short Column Design - Engineering
by.genie.uottawa.casteel yield strength 60.0 ksi, the intermediate strain line for 035εt =0. has been plotted. For Steel yield strength 75.0 ksi, the intermediate strain line for 038εt =0. has been plotted. It should be noted that all strains refer to those in the reinforcing bar or bars farthest from the compression face of the section.
Datasheet 4340 ALLOY STEEL – AMS 6414 VAR – UNSG43406
www.ssa-corp.com4340 VAR AMS 6414 is a low alloy Chromium-Nickel-Molybdenum steel capable of being heat treated to high strength levels. This specification is for a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. Service Steel Aerospace stocks Premium Aircraft Quality produced double melted in an ...
IS : 1786 - 2008 - Visakhapatnam Steel Plant
www.vizagsteel.comCombination of high strength and high ductility VIZAG TMT bars have rare combination of high strength with excellent ductility. The tensile to yield strength ratios are always greater than 1.12. In normal bars, the increase in the yield strength of the bars is accompanied by the loss of percent elongation. But
An Overview of Open Web Steel Joists
www.wje.comdesign, manufacture, and erection of steel joist construction. The first SJI Specification permitted the use of rolled shapes or strips of sheet steel, round bars, angles or specially rolled bars riveted or welded together. Modern-day open web steel joists are similar to those produced in the 1920s and 1930s, and all
SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM ... - DIYTrade
doc.diytrade.comStainless Chromic-Nickel Steel- Clad Plate, Sheet, and Strip G 3601 (2) 3740 (2) 17440/1 A-265 Nickel and Nickel-Base Alloy-Clad Steel Plate G 3602 (2) --- 17743 NiCu30Fe A-283 Low and Intermediate Tensile Strength Carbon Steel Plates, Shapes, and Bars
RULES FOR CLASSIFICATION Ships Part 3 Hull Chapter 3 ...
rules.dnv.comSteel having ReH > 390 N/mm 2 is regarded as extra high strength structural steel. In the following, material grades of hull structural steels are referred to as follows: a) A, B, D, E and F denote normal strength steel grades. b) AH, DH, EH and FH denote high strength and extra high strength steel grades, where H indicates the material strength.
Datasheet for Steel Grades Carbon Steel SAE 1010
www.steel-grades.comSteel GradesSAE 1010 Chemical information,Mechanical properties Physical properties, Mechanical properties, Heat treatment, and Micro structure SAE 1010 Physical Properties Tensile strength 115-234 σb/MPa Yield Strength 23 σ 0.2 ≥/MPa Elongation 65 δ5≥ (%) ψ - ψ≥ (%) Akv - Akv≥/J HBS 123-321 - HRC 30 - SAE 1010 Mechanical Properties
pl LRFD ASD - Structural Engineering Software
www.asdipsoft.comrequired moment strength, Mu pl or Ma pl, for a 1-in. strip of plate due to the tension in the anchor rods is The required moment strength due to the bearing stress distribution is critical. The required plate thickness is: Use a 14 × 14 × 1 -in. base plate. 4. Determine the required tensile strength of the anchor rod. 5.
LONGSPAN AND DEEP LONGSPAN STEEL JOISTS, LH-AND …
images.ebsco.comA370 and the specimens shall exhibit a yield strength equal to or exceeding the design yield strength and an elongation of not less than (a) 20 percent in 2 inches (51 mm) for sheet and strip or (b) 18 percent in 8 inch-es (203 mm) for plates, shapes and bars with adjust-ments for thickness for plates, shapes and bars as pre-