HILTI TECHNICAL BULLETIN
Mar 04, 2018 · Tables in this technical bulletin are developed based on the Allowable Stress Design approach using published data in ESR-4143, ESR-4144, and internal testing information. Section 2.2.2 of the Hilti North American Product Technical Guide, Volume 2: Anchor Fastening Technical Guide, Edition 17 (2017 PTG) provides detailed
Download HILTI TECHNICAL BULLETIN
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1/8 Safety Data Sheet acc. to ISO 11014 - Hilti USA
www.hilti.comPage 2/8 Safety Data Sheet acc. to ISO 11014 Printing date 05/19/2015 Version number 5 Reviewed on 05/19/2015 (Contd. of page 1) 40.2.7 H319 Causes serious eye irritation.
Hilti. Outperform. Outlast.
www.hilti.comSelector Guide Through-Penetration Joint Reference Data Firestop Mortar (CP 637) Product description ... Concrete and masonry assemblies Expansion on setting (approx.)Walls and floors rated up to 4 hours ... Mix ratio (recommended, mortar to water):
ICC-ES Evaluation Report ESR-2269 - Hilti
www.hilti.com1.0 EVALUATION SCOPE Compliance with the following codes: 2018, 2015, and 2012 International Building Code ® (IBC) 2018, 2015, and 2012 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2269 LABC and LARC Supplement.
HIT-RE 500 V3 - Hilti
www.hilti.comSafety information for 2-Component-products 18/06/2020 US-OSHA - en 2/27 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.
Hilti HIT-HY 200 with HIT-V
www.hilti.comAnchor rods HIT-V GR / -HCR) are available in variable length MIO M12 TE 16 M16 M20 M24 TE 40 M27 - TE 70 M30 compressed air gun or blow out pump, set of cleaning brushes, dispenser Drill hole to the required embedment depth with an appropriately sized Hilti TE-CD Or TE-YD hollow drill bit with Hilti vacuum attachment. This drilling
Hilti HIT-HY 200 with rebar
www.hilti.comHilti HIT-HY 200 with rebar Benefits - suitable for cracked and non- cracked concrete C 20/25 to C 50/60. - Approved automatic cleaning with the use of the hollow drill-bit high loading capacity, excellent handling HY 200-R version with extended curing time for rebar applications small edge distance and anchor spacing possible
KB-TZ2 TECHNICAL GUIDE
www.hilti.comKB-TZ2 Technical uide April 2021 5 Table 4 - Allowable Hilti carbon steel KB-TZ2 strength in uncracked concrete for hammer drill and core drill installations 1,2,3,4 Nominal anchor
OPENINGS IN COMPOSITE FLOOR DECKS - Hilti
www.hilti.comin-situ reinforced concrete topping. The decking not only acts as a permanent formwork to the concrete, but also provides sufficient shear bond with the concrete so that, when the concrete has cured, the two materials act together compositely to resist the loads on the deck. Openings in floor decks are a common part of any building.
HIT-1 ADHESIVE ANCHORING SYSTEM - Hilti
www.hilti.comHIT-1 ADHESIVE ANCHORING SYSTEM Technical Supplement PRODUCT DESCRIPTION Hilti HIT-1 is a hybrid adhesive mortar combining resin, hardener, cement, and water. It’s formulated for fast curing and easy installation in a wide range of concrete and masonry base materials with temperatures ranging from 32°F (0°C) up to 95°F (35°C).
ICC-ES Evaluation Report ESR-4266
www.hilti.comDesign strength of anchors complying with the 2012 IBC as well as Section R301.1.3 of the 2012 IRC, must be determined in accordance with ACI 318-11 Appendix D and this report. Design parameters provided in Table 4, Table 5, Table 6 and Table 7 of this report are based on the 2021 IBC (ACI 318-19), 2018 and 2015 IBC (ACI 318-14) and the 2012 IBC
Related documents
Technical Bulletin TB-04 - Owens Corning
www.owenscorning.comSep 20, 2017 · 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
TECHNICAL SERVICE BULLETIN 19-2132 3.5L EcoBoost/2.7L ...
static.nhtsa.govTECHNICAL SERVICE BULLETIN 3.5L EcoBoost/2.7L EcoBoost - Illuminated MIL With DTC P04F0 And/Or P144C 19-2132 30 April 2019 Model: Issue: Some 2018-2019 F-150 vehicles equipped with a 3.5L EcoBoost or 2.7L EcoBoost engine and some 2018-2019 Expedition and Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated
TECHNICAL SERVICE BULLETIN 20- Lack Of Heat Or Cooling ...
static.nhtsa.govBulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was …
Technical Bulletin TB-04
www.owenscorning.comSep 20, 2017 · 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.