INSTALLER'S GUIDE
4. Remove approximately 3" of gasket material from the bottom of each corner post to expose the holes used to attach the economizer assembly to the unit, as illustrated in Figure 6 Figure 5 5. With the screws provided, secure both sides of the economizer assembly by inserting the screws, through the clearance holes in the bottom of the corner post,
Download INSTALLER'S GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
Chiller perormancf e testing program - Trane
www.trane.com2 Chiller performance testing Trane is the global chiller leader Trane has manufactured centrifugal chillers in La Crosse since 1938. Much more than a
Water-Cooled Liquid Chiller Model CVGF 400 to …
www.trane.comIntroducing Trane’s Model CVGF Centrifugal Water Chiller Introduction The basic gear driven centrifugal water chiller design was introduced in 1976 and has been
3-D™ SCROLL COMPRESSOR NOMENCLATURE - …
www.trane.com3-D™ SCROLL COMPRESSOR NOMENCLATURE C S H A 1 5 0 K 0 * 0 0 Digit1 23 456789 101112 Digit 1 C ♦ Positive displacement …
Trane® Voyager
www.trane.comTrane combines technological innovation with legendary reliability and performance to create the lowest cost of ownership. Trane® Voyager™ rooftop units not only offer the lowest installed cost, they also can reduce
Packaged Cooling with Electric Heat Rooftop Units
www.trane.comPackaged Cooling with Electric Heat Rooftop Units Voyager™ 12½ - 25 Tons - 60 Hz December 2003 RT-PRC002-EN
Packaged Cooling with Electric Heat Rooftop Units
www.trane.comPackaged Cooling with Electric Heat Rooftop Units Precedent ™ 3 - 10 Tons — 60 Hz March 2003 RT-PRC005-EN
Air Conditioners - Trane
www.trane.comThe XV20i shown is for illustration purposes only. Please note that features and components may vary by model. As part of our continuous product improvement, Trane reserves the right to change specifications and design without notice.
Split System Heat Pumps
www.trane.comSSP-PRC001-EN 5 Odyssey air handler versatility is fur-ther increased by a complete line of accessories designed to match and install smoothly:
Split System Cooling Units - Heating and Air …
www.trane.comSplit System Cooling Units TTA075A-TTA200B Air Handlers TWE050A-TWE200B 50 Hz Split System Cooling Units December 2000 SS-PRC003-EN
Trane Packaged Systems - Heating and Air …
www.trane.comFlexible enough to install where you need it. Tough enough to be a Trane. Trane packaged heating and cooling systems give you everything in one.
Related documents
Gasket Selection Guide B-03 - Shurjoint
www.shurjoint.comGasket Selection Guide B-03 B-03-1/6 Rev.N 20160314 GASKET SELECTION GUIDE Over the past 50 years great advances have been made in synthetic elastomer technologies, allowing us to offer a full range of gasket materials for a wide variety of piping applications. Shurjoint utilizes the finest materials available in our gaskets
CROSBY J-SERIES DIRECT SPRING PRESSURE RELIEF VALVES
www.flotechinc.com(1.03 to 413.79 barg) JBS-E: 15 to 6000 psig (1.03 to 413.79 barg) JLTJBS-E: 25 to 6000 psig ... results in selection of a smaller valve with an associated reduction in inlet and discharge piping costs. ... 27 Set screw gasket[1] 316 SS 28 Guide gasket[1] 316 SS 30 Pipe plug (bonnet) CS 34 Seal and wire Lead and SS
TOMBO BRAND GASKETS
www.nichias.co.jp43JIS B 2251：2008 “Bolt tightening procedure for pressure boundary flanged joint Assembly” Design standards of gaskets Standard dimension of gaskets
CROSBY J-SERIES DIRECT SPRING PRESSURE RELIEF VALVES
www.emerson.com(1.03 to 413.79 barg) JBS-E: 25 to 6000 psig (1.72 to 413.79 barg) JLTJBS-E: 25 to 6000 psig ... results in selection of a smaller valve with an associated reduction in inlet and discharge piping costs. ... 27 Set screw gasket[1] 316 SS 28 Guide gasket[1] 316 SS 30 Pipe plug (bonnet) CS 34 Seal and wire Lead and SS
LKQ Parts Guide - LKQ Corporation
www.lkqcorp.comContact your nearest location by calling (866) LKQ-CORP or visit us onilne at LKQCorp.com 1 LKQ Corporation is always working harder to do more for you and your car with the nation’s largest supply of quality used auto parts.
MECHANICAL SEAL SELECTION GUIDE - Hi-Tech Seals Inc.
www.hitechseals.comMECHANICAL SEAL SELECTION GUIDE. The Complete Cross Reference for Mechanical Face Seal Replacement ... Cup Gasket 2. Stationary Face 3. Rotary Face 4. Bellow 5. Spring Retainer 6. Spring 7. Drive Shell 8. Drive Ring 1. Cup Gasket ... 137 52 …
Flexmaster Joints - Eaton
www.eaton.com†† Maximum temperature ratings are meant as a guide only. ... 76.2 - 152.4 (1.03 MPa) (1.03 MPa) ... An important consideration in the selection of a gasket material is to avoid undesirable chemical reaction between the agent carried and the gasket material. The gasket selector chart
Curtain Wall Systems - Kawneer
www.kawneer.comThe selection of mullion is dependent on several factors: The span (the distance between the fixings to supporting structure) The mullion centres (up to 3.0m using AA ®100 curtain walling) Windload (up to 2400 Pa) Maximum weight of infill is 600kg The …
Anvil International, Inc. - Hayward Pipe
www.haywardpipe.comASTM D2000 for each gasket grade. Refer to the Gruvlok Gas-ket Selection Guide for details. ANSI Bolts and Heavy Hex Nuts: Heat treated, oval neck track head bolts conforming to ASTM A183 Grade 2 with a minimum tensile strength of 110,000 psi and heavy hex nuts of carbon steel conforming to ASTM A563.