INSULATED ROOFING, - Stratco
The innovative Cooldek® insulated panel provides a roof, insulation and ceiling like fi nish all in one product. With superior spanning capabilities, two roof profi les and fi ve insulation thicknesses to choose from, it is an ideal solution for domestic patio roof applications.
Download INSULATED ROOFING, - Stratco
Information
Domain:
Source:
Link to this page:
Documents from same domain
STRATCO FRONTIER ASSEMBLY INSTRUCTIONS.
www.stratco.com.au7.0BARGECAPPING Only the front and two sides of the carport require the attachment of barge capping. The rear has the gutter attached. Fix the side barge capping first.
Purlins & Girts - stratco.com.au
www.stratco.com.au1 The Stratco Capacity Tables have been calculated in accordance with limit state design principles and comply with the Australian/ New Zealand Standard AS/NZS 4600:2005 Cold-formed steel
INSULATED ROOFING,
www.stratco.com.auFor Cooldek roofi ng in attached or freestanding domestic gable patio application, sheet spans shall not exceed those given for one or no open sides. Alternatively, Table 3.0 indicating wind capacities may be used to determine allowable single spans for any application. Spans specifi ed for units with three sides open are suitable for
Cooldek Outback Flat Attached Installation Guide
www.stratco.com.auIt is the builder’s responsibility to ensure any existing structure that an Outback is being attached to is adequately reinforced to accommodate the additional loads imposed by the verandah, patio or carport. Read these instructions thoroughly before starting your project and refer to them constantly during each stage of construction.
OVERFLOW SOLUTIONS - Stratco
www.stratco.com.ausystem (who may be the architect, builder, hydraulic engineer, home owner, roofing or guttering contractor) to design a ... The following overflow solutions provide a measure for continuous overflow for the full length in which the solution is applied.
POST & RAIL FENCING 1300 155 155 SCAN THIS QR CODE TO …
www.stratco.com.auStratco Post & Rail fencing is a traditional and cost e˜ ective form of fencing. Its simple design makes it the ideal choice for a ... Fence capping is placed over the top edge of the fence sheet with the long side of the capping facing the post and rail side of the fence. The capping is slightly tapered to allow for overlapping.
Roller Door - Stratco
www.stratco.com.audoor to be installed and if the headroom is a restricted space. • If the roller door is installed with a headroom greater then those listed in the Headroom Measurements table, the resulting daylight opening will be reduced. • If the roller door is installed significantly below the top of the
Fencing Frameless Glass Catalogue - Sheds | Fencing | Roofing
www.stratco.com.au12mm Fully Frameless Glass flat polished edges 5mm radius corners 01 Stratco Order Code G.O. Order Code Width Sqm Corner Radius Glass Weight KGS ... base plate - 10mm thick 95mm 73mm inner hole diameter 12mm 95mm 73mm 26 11 100 187 127 95 NOT TO SCALE 60 NOT TO SCALE 21 239 111 52 128 52 • Stainless Steel 2205
WIND CLASSIFICATION, - Stratco
www.stratco.com.auN1 (Non-Cyclonic) N/A W28 N2 (Non-Cyclonic) N/A W33 N3 (Non-Cyclonic) C1 (Cyclonic) W41 N4 (Non-Cyclonic) C2 (Cyclonic) W50 N5 (Non-Cyclonic) C3 (Cyclonic) W60 N6 (Non-Cyclonic) C4 (Cyclonic) W70 TERRAIN CATEGORY The wind speed at a structure is infl uenced by the terrain it fl ows over as it approaches the structure. The terrain category
SUPERDEK - Stratco
www.stratco.com.auRoofing calculations are based on Cpe=-0.9 and Cpi=0.2, walling is based on Cpe=-0.65 and Cpi=0.2. A local pressure factor, Kl=2.0 has been used for all roofing spans for both strength and serviceability limit states. Roof spans take into consideration loads incidental to maintenance. All pressures have been determined assuming wind
Related documents
Insulation requirements - Tenancy Services
www.tenancy.govt.nzTable 2. Ceiling or roof framing is commonly 90 mm deep, so insulation should be within 20 mm of the top of the ceiling or roof framing, if not above it. If the insulation sits below the roof framing, this means it has settled, and will continue to settle over time to …
NUCOR CFR™ STANDING SEAM ROOF SYSTEM TABLE OF …
www.nucorbuildingsystems.cominsulated roof areas. Tall Clips: Maximum of 8” of single layer batt insulation is allowed, which requires special attention to maintain panel modularity and thermal performance. Super Tall Clips Maximum of 12” combined layers of batt insulation is allowed,
XPS Roof Insulation - Owens Corning
www2.owenscorning.comlow slope single ply insulated roof systems page 9 prma, vegetative and plaza deck insulated roof systems page 10 recover roofing insulated roof systems page 11 architectural metal insulated roof systems page 12 foamular® tapered xps roof insulation systems page 13 key differences between xps and other rigid foam insulations page 14
ROOF MAINTENANCE GUIDE - Roofing Contractors …
www.rcabc.orgConventional Insulated Roof membrane is installed directly over insulating materials, which are installed on the deck (wood, concrete or steel). The membrane is exposed to the weather. Protected (or Inverted) Membrane Roof membrane is installed directly to the deck (wood, concrete or overlaid steel). Extruded
Roof Curbs, Extensions and Equipment Supports Rev 6 ...
content.greenheck.comuse on both insulated (GESR) and non-insulated (GESS) flat roof decks. They are mounted directly to the deck structure, then roofed and flashed for weather tightness. Models GESS and GESR are available in welded aluminum or galvanized steel. Heights of 8, 12 and 14 inches (203, 305 and 356 mm) Widths of 4, 6 and 8 inches (102, 152 and 203 mm)
Installer's Guide - Roof Curb Packaged Rooftop Units.
www.trane.comNote: All field fabricated panels used must be insulated.(See Figure 5, p. 8, Figure 12, p. 11, or Figure 19, p. 15). Roof Opening For safety and sound considerations, do not cut out the entire roof deck within the curb area. Roof Support WARNING Heavy Objects!
Insulated Metal Panels - All Weather Insulated Panels
www.awipanels.companels. Insulated metal panels are installed as a single element allowing for faster building completion in almost any kind of weather without risk to system integrity, as opposed to multiple installation steps for other insulated wall and roof systems. The lightweight wall and roof panels are available in a wide range of long lasting finishes
FACTORY-BUILT A MAJOR CAUSE OF INSULATED CHIMNEY …
www.selkirkcorp.comrecommended that the chimney be enclosed below the roof line to protect the chimney from cold outdoor temperatures, this may help reduce condensation, creosote formation and enhance draft. Provide an access door by the Tee Plug for chimney inspection and cleaning. The exterior enclosure may be insulated, maintaining