INSULATION FOR THE BUILDING ENVELOPE
• Tested per NFPA 285 to comply with IBC Section 2603.5.5 • Tested per NFPA 286 (ICC-ES AC12 Appendix B) • Water-Resistive Barrier (WRB) per ICC-ES AC71 (ASTM E331, AATCC Test Method 127) • Class A Flame Spread and Smoke Developed Indices per IBC Chapter 8, Interior Finishes (1” min.) • 1, 2, 3 or 4 hour Fire Rated Assemblies as shown
Download INSULATION FOR THE BUILDING ENVELOPE
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET Sika® Primer-207
usa.sika.comIMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under worst case conditions are man-datory. Sika® Primer-207 is a moisture reactive sys-
Sikadur Epoxies Application Guide - Sika …
usa.sika.comSikadur® Epoxies Application Guide LPL = Long Pot Life cps = centipoise Reference approximate viscosity water = 1 cps olive oil = 100 cps motor oil = 1000-2000 cps Crack Repair Patching Overlay Bonding Adhesive Anchor Bolts Base Plate Grouts USDA Approved Potable Water Approved ASTM C-881 Interior Exterior Int. Exterior Type …
Liquid Seam Sealant - Sika AG
usa.sika.comConstruction Sikaflex® 110 Liquid Seam Sealant Description Sikaflex 110 Liquid Seam Sealant is a non-shrinking, 100% solids, solvent free polyether based, moisture curing, elastomeric sealant. It forms a weather-tight seal when applied over sheathing board joints.
Part 1 - General - Sika AG
usa.sika.comA. Sikadur Injection Gel as manufactured by Sika Corporation, 1682 Marion Williamsport Road, Marion, Ohio 43302 is considered to conform to the requirements of this specification.
PRODUCT DATA SHEET SikaTop®-123 Plus
usa.sika.com0 g/l (EPA method 24) LIMITATIONS Do not use solvent-based curing compound. Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R. If aggressive means of substrate preparation is
SikaSwell S-2 SikaSwell S-2
usa.sika.comApplication Recommended application temperatures: 50°-90°F. Extrude material using Sika MK-5 bulk caulking gun or other approved bulk gun. Cut the nozzle to obtain a triangular extrusion section with a size fulfilling effective needs (or use nozzle included in carton of SikaSwell S-2). Apply a uniform, continuous bead to the hardened concrete.
PRODUCT DATA SHEET Sikalastic®-710 Base
usa.sika.comMetal - Should be thoroughly cleaned by grinding or blast cleaning to near white metal (SSPC SPS-10). Priming Primer Selection - Determine maximum moisture content of concrete substrate by weight with a Tramex CME or CMExpert type concrete moisture meter. Sikalastic® Primer – For concrete decks with a maximum
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comSpecification TT-S-00230C, Type II, Class A. Meets ASTM C-920, Type S, Grade NS, Class 35, use T, NT, O, M, G, I, A. Canadian standard CAN/CGSB 19.13-M87. USES Designed for all types of joints where maximum depth of sealant will not exceed 1/2 in. Excellent for small joints and fillets, windows, door
PRODUCT DATA SHEET Sika® FerroGard®-903
usa.sika.comreinforced, prestressed, precast, post tensioned or marine concrete. Use of Sika® FerroGard®-903: Steel-reinforced concrete, bridges and highways exposed to corrosive environments (deicing salts, weathering) Building facades and balconies Steel-reinforced concrete in or near a marine environment Parking garages
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comJoint dimension should allow for 1/4 inch minimum and 1/2 inch maximum thickness for sealant. Proper design is 2:1 width to depth ratio, For use in horizontal joints in traffic areas, the absolute minimum depth of the sealant is 1/2 in. and closed cell backer rod is recommended. Removal Use personal protective equipment (chemical resistant
Related documents
NFPA 285 Fire Tested Wall Assemblies - Insulation
insulation.owenscorning.comCOMMERCIAL COMPLETE WALL SYSTEM NFPA 285 Tested Wall Assemblies FOAMULAR® Insulation, JointSealR™ Foam Joint Tape, EcoTouch™ Flame Spread 25, EcoTouch™ Thermal Batt FIBERGLAS™ Insulation NFPA 285 Fire Tested Wall Assemblies Owens Corning’s Commercial Complete Wall System has successfully passed the NFPA 285* fi re test in many …
LIST OF NFPA CODES & STANDARDS
hamyarenergy.comNFPA 274 Standard Test Method to Evaluate Fire Performance Characteristics of Pipe Insulation NFPA 275 Standard Method of Fire Tests for the Evaluation of Thermal Barriers Used Over Foam ... NFPA 285 Standard Fire Test Method for Evaluation of …
DC315 Intumescent Coating - Intumescent Fire Retardant ...
painttoprotect.comcomponent of exterior wall systems in accordance with the NFPA 285 and meets IBC Section 2603.5 with various architectural cladding options. The Choice is clear, DC315 is the most tested and approved fire protective coating for SPF insulation on the market today! DC315 Tested Solutions for Spray Polyurethane Foam
DC315 Intumescent Coating - mystagingwebsite.com
painttoprotect.comcomponent of exterior wall systems in accordance with the NFPA 285 and meets IBC Section 2603.5 with various architectural cladding options. The Choice is clear, DC315 is the most tested and approved fire protective coating for SPF insulation on the market today! DC315 Tested Solutions for Spray Polyurethane Foam
DuPont Thermax Sheathing
www.dupont.comSystem Incorporating Thermax ™ Insulation Tested in Accordance With NFPA 285, 2019, 2018, 2015, 2012, 2009 and 2006 Editions (UBC 26.9, intermediate scale – multistory testing) • NFPA 285 compliant when installed as part of exterior wall assemblies in ICC-ES ESR-1659 or valid engineering judgement reports
AP Foil-Faced - Insulation Systems, Commercial Roofing and ...
www.jm.com• NFPA 259, Standard Test Method for Potential Heat of Building Materials •A 285, Standard Fire Test Method for Evaluation of Fire Propagation Characteristics of NFP Exterior Non-Load-Bearing Wall Assemblies Containing Combustible Components • AC 71, Acceptance Criteria for Foam Plastic Sheathing Panels Used as Water-Resistive Barriers