INSULATION FOR THE BUILDING ENVELOPE
type of fastener and its capacity; consult fastener manufacturer. Fasten to wood framing using cap nails, washers with roofing nails, or washers with bugle head screws. When used in conjunction with Thermasheath®-SI, staples at 12” o.c. pattern may be used to fasten Thermasheath®. With staples, Rmax recommends taping the joints as soon
Download INSULATION FOR THE BUILDING ENVELOPE
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET Sika® Primer-207
usa.sika.comIMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under worst case conditions are man-datory. Sika® Primer-207 is a moisture reactive sys-
Sikadur Epoxies Application Guide - Sika …
usa.sika.comSikadur® Epoxies Application Guide LPL = Long Pot Life cps = centipoise Reference approximate viscosity water = 1 cps olive oil = 100 cps motor oil = 1000-2000 cps Crack Repair Patching Overlay Bonding Adhesive Anchor Bolts Base Plate Grouts USDA Approved Potable Water Approved ASTM C-881 Interior Exterior Int. Exterior Type …
Liquid Seam Sealant - Sika AG
usa.sika.comConstruction Sikaflex® 110 Liquid Seam Sealant Description Sikaflex 110 Liquid Seam Sealant is a non-shrinking, 100% solids, solvent free polyether based, moisture curing, elastomeric sealant. It forms a weather-tight seal when applied over sheathing board joints.
Part 1 - General - Sika AG
usa.sika.comA. Sikadur Injection Gel as manufactured by Sika Corporation, 1682 Marion Williamsport Road, Marion, Ohio 43302 is considered to conform to the requirements of this specification.
PRODUCT DATA SHEET SikaTop®-123 Plus
usa.sika.com0 g/l (EPA method 24) LIMITATIONS Do not use solvent-based curing compound. Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R. If aggressive means of substrate preparation is
SikaSwell S-2 SikaSwell S-2
usa.sika.comApplication Recommended application temperatures: 50°-90°F. Extrude material using Sika MK-5 bulk caulking gun or other approved bulk gun. Cut the nozzle to obtain a triangular extrusion section with a size fulfilling effective needs (or use nozzle included in carton of SikaSwell S-2). Apply a uniform, continuous bead to the hardened concrete.
PRODUCT DATA SHEET Sikalastic®-710 Base
usa.sika.comMetal - Should be thoroughly cleaned by grinding or blast cleaning to near white metal (SSPC SPS-10). Priming Primer Selection - Determine maximum moisture content of concrete substrate by weight with a Tramex CME or CMExpert type concrete moisture meter. Sikalastic® Primer – For concrete decks with a maximum
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comSpecification TT-S-00230C, Type II, Class A. Meets ASTM C-920, Type S, Grade NS, Class 35, use T, NT, O, M, G, I, A. Canadian standard CAN/CGSB 19.13-M87. USES Designed for all types of joints where maximum depth of sealant will not exceed 1/2 in. Excellent for small joints and fillets, windows, door
PRODUCT DATA SHEET Sika® FerroGard®-903
usa.sika.comreinforced, prestressed, precast, post tensioned or marine concrete. Use of Sika® FerroGard®-903: Steel-reinforced concrete, bridges and highways exposed to corrosive environments (deicing salts, weathering) Building facades and balconies Steel-reinforced concrete in or near a marine environment Parking garages
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comJoint dimension should allow for 1/4 inch minimum and 1/2 inch maximum thickness for sealant. Proper design is 2:1 width to depth ratio, For use in horizontal joints in traffic areas, the absolute minimum depth of the sealant is 1/2 in. and closed cell backer rod is recommended. Removal Use personal protective equipment (chemical resistant
Related documents
IS 1364-1 (2002): Hexagon Head Bolts, Screws and Nuts of ...
law.resource.orgbasic data IS 1367 (Part 17):1 99621 Industrial fasteners— Threaded steel fasteners—Technical supply conditions : Part 17 inspection, sampling and acceptance procedure (third revision) IS 1367 (Part 14/See 1):2002 Technical supply conditions for threaded steel fasteners: Part 14 Mechanical properties of corrosion resistant stainless-
Fastener Design Manual - NASA
ntrs.nasa.govFastener Design Manual Richard T. Barrett March 1990 The manual describes various platings that may be used for corrosion control including cadmium and zinc plating. It does not mention outgassing problems caused by the relatively high vapor pressure of these metals. The fastener manual was intended primarily for aeronautical applica-
Nail Withdrawal Strength and Nailhead Pull-Through of ...
www.apawood.orgapplied along the axis of the fastener: shank withdrawal from the lumber and nailhead pull-through of the sheathing material. Under certain circumstances, such as strong gusts of wind, hurricanes, or seismic activity, shingles or siding may be …
Hilti - 2011 Anchor Fastening Technical Guide
www.buildsite.comThe Anchor Fastening Technical Guide is intended to We passionately create enthusiastic customers and build supplement the Hilti Product and services catalog with technical information for the designer or specifier. Technical data presented herein was current as of the date of public a-tion (see back cover). Load values are based on testing and
EnergyGuard Polyiso Insulation 20 & 25 PSI Data Sheet - GAF
www.gaf.comtheir placement are subject to change without notice. Consult RoofNav and FM Global Loss Prevention Data Sheets 1-28, 1-29, and 1-29R for approved fastener density for Polyisocyanurate Roof Insulations. If your fastener pattern is not listed, please contact Technical Services at …
Fastener Loads for Plywood – Screws
www.grabberman.comTECHNICAL NOTE THE ENGINEERED WOOD ASSOCIATION APA Number E830D • August 2005 INTRODUCTION The integrity of a structure is frequently dependent upon the connections between its component elements. For maximum strength and stability, each joint requires a design adapted to the fastener type and to the strength properties of the individ-
ADVANTECH® SHEATHING - Huber Engineered Woods
www.huberwood.com800.933.9220 • Technical Service: 800.933.9220 x2716 ZIPSystem.com • HuberArchitectLibrary.com . BASIC USE AND APPLICATIONS . AdvanTech® sheathing is a high-performance engineered panel designed to replace plywood and commodity oriented strand board (OSB) for roof, wall, and -layer 2 floating subfloor system applications.