ISCAR Grades Chart

Nuances ISCAR - ISCAR Cutting Tools

S.T.SUMO TEC Standard Semi-standard Nuances ISO Couches de revêtements Applications TRONÇONNAGE GORGES USINAGE FRONTAL TOURNAGE ISO FILETAGE PERÇAGE FRAISAGE IC300 REVÊTUE PVD P25-P50 M20-M40 S15-S25 TiN TiCN Nuance tenace micrograins revêtue TiCN/TiN PVD.

  Nuance, Iscar, Nuances iscar

ISCAR Grades Chart - ISCAR Cutting Tools

Grades for Applications and Materials Material Groups Main Applications ISO P ISO H ISO M ISO S ISO K ISO N 1-11 Steel 38-41 Hard Steel 12-14 Stainless

  Chart, Cutting, Grade, Iscar grades chart, Iscar

ISCAR Grades Chart

DR drills. S.T. IC8150 P01-P30 K05-K15 M05-M15 TiCN Al203 TiN A very hard substrate with a cobalt enriched layer, MTCVD TiCN and a thick Al 2 O 3 CVD coating. Features excellent thermal stability and resistance to chipping and plastic deformation. Recommended for high speed machining of steel at stable or slightly unstable conditions. S.T ...

  Drill

40,000 - Iscar

MM FF - 2 10-20 37 E MM EFF - 4, 6 8-25.4 38 MM HT - 2 10-20 39 E MM HT-NCSR - 2 12 40 MM HT-NWFR - 2 12 40 MM ETR 30° 6 8-16 41 MM HCR - 2 8-16 General Finishing 43 E MM HRF - 2 8-16 General Finishing 43 E MM HBR - 2 10-25.4 44 E MM EB 30° 2, 4 6-20 45 MM EBA 45° 2 8-25 For Machining Aluminum 45 MM HC 10° 2 7.8-16 47 MM ECU 38° 3 7.7-19.7 ...

ISCAR Grades Chart

A 55% CBN brazed tip, used for finishing hardened steel (45-65 HRc) in continuous cutting. ID5 N01-N10 A PCD brazed tip, suitable for machining aluminum (Si < 12%) and copper alloys and general cutting of nonferrous materials. ID8 N05-N15 PCD grade for milling applications. Ideal for machining nonferrous metals, such as high silicon (>12%)

Solid Carbide Drills Speed and Feed Recommendations

Solid Carbide Drills Speed and Feed Recommendations SPEEDS and FEEDS are suggested starting points only and may be increased or decreased depending on actual material and

  Speed, Recommendations, Feed, Drill, Solid, Carbide, Solid carbide drills speed and feed recommendations

COATINGS & SUBSTRATES CHART - Harvey Tool

TECHNIC ORMATION 368 Coating/ Substrate: TiN AlTiN AlTiN Nano Titanium Nitride-C1 Aluminum Titanium Nitride-C3 Aluminum Titanium Nitride Nano-C6 Application/

  Chart, Substrates, Coating, Titanium, Coatings amp substrates chart

Heat Treatment of Cast Irons - Heat Treat Doctor.com

carbon. The surface of chilled iron castings is extremely hard. The depth and hardness of the chilled portion may be controlled by adjusting the composition of the metal.

  Treatment, Heat, Cast, Iron, Heat treatment of cast irons

Understanding Valve Design and Alloys - sbintl.com

Performance and Heavy-Duty Valve Alloys Materials that are commonly used for performance valve applications include carbon steel alloys, stainless steels, high-strength nickel-chromium-iron alloys and titanium.

  Design, Understanding, Valves, Alloys, Titanium, Understanding valve design and alloys

Chapter 4 Alloys - University of Wisconsin–Oshkosh

4 - 1 CHAPTER 4: ALLOYS And there came out from the camp of the Philistines a champion named Goliath, of Gath, whose height was six cubits and a span.

  University, Chapter, Wisconsin, Chapter 4, Alloys, Oshkosh, Chapter 4 alloys, University of wisconsin oshkosh

Development of Ni-Co-Base Alloys for High-Temperature Disk ...

DEVELOPMENT OF Ni-Co BASE ALLOYS FOR HIGH-TEMPERATURE DISK APPLICATIONS Y. F. Gu 1, C. Cui , H. Harada , T. Fukuda1, 2, D. Ping1, A. Mitsuhashi2, K. Kato2, T. Kobayashi1 and J. Fujioka1 1High Temperature Materials Center, National Institute for Materials Science 1-2-1 Sengen, Ibaraki 305-0047, Japan 2 Non-Ferrous Alloys Research and Technology Laboratory, Mitsubishi Materials Corporation ...

  Alloys