Keysert and Keensert - Howmet Aerospace
Drill out old threads with a standard drill. Note: Drill is oversize — see charts for proper dimensions. Chamfer the hole with a standard countersink (82°-100°). Tap new threads with a standard tap. See charts for proper size and depth. Screw in the insert until slightly below surface. Drive keys down with several hammer taps on the proper
Download Keysert and Keensert - Howmet Aerospace
Information
Domain:
Source:
Link to this page:
Related documents
Inch/MetrIc tap DrIll SIzeS & DecIMal equIvalentS
www.brokenbolt.commetric tap Drill SizeS metric tap tap Drill (mm) Decimal (inch) m1.6 x 0.35 1.25 .0492 m1.8 x 0.35 1.45 .0571 m2 x 0.4 1.60 .0630 m2.2 x 0.45 1.75 .0689 m2.5 x 0.45 2.05 .0807 m3 x 0.5 2.50 .0984 m3.5 x 0.6 2.90 .1142 m4 x 0.7 3.30 .1299 m4.5 x 0.75 3.70 .1457 m5 x 0.8 4.20 .1654 m6 x 1 5.00 .1968 m7 x 1 6.00 .2362 m8 x 1.25 6.70 .2638 m8 x 1 7 ...
TAP DRILL SIZES INCH / METRIC EQUIVALENT - Emuge
www.emuge.comTAP DRILL SIZES INCH / METRIC EQUIVALENT Thread Size Tap Drill Size Thread Size Tap Drill Size Cut Thread Form Thread Inch Metric Cut Thread Form Thread Inch Metric #0-80 0.0472 1.20 M10x0.75 0.3622 9.20 #0-80 0.0551 1.40 M10 0.3681 9.35 #1-64, #1-72 0.0595 1.51 7/16-14 0.3701 9.40
STANDARD TAPS SPEED RECOMMENDATIONS - Industrial …
industrial-tool-supply.comtap drill sizes – sti (screw thread insert) taps aluminum steel, plastic, magnesium decimal minor dia. limits (after tapping) decimal minor dia. limits (after tapping) sti tap equiv. of tap equiv. of tap drill tap drill drill tap drill size size (inches) min. max. size (inches) min. max. 4 - 40 #31 .1200 .116 .121 #31 .1200 .119 .124
& Components for Industrial Bulletin 998 - Mutual Screw
www.mutualscrew.comDRILL Drill out the damaged threads using the drill supplied in the kit. Drill to a sufficient depth to accommodate the insert length and the bolt or screw being used. TAP Tap the hole using the Heli-Coil tap supplied in the kit. Check the size on the shank of the tap to be sure it is the right size. Tap the hole to sufficient depth to ac-
Tapping Drill Sizes
www.ajhw.co.uktap size drill size tap size drill size tap size drill size tap size drill size 1 x 0 .25 0 .75 4 x .35 3.6 No. 1 x 64 No. 53 1.5 No. 0 x 80 3/64" 1.2 1.1 x 0.25 0 .85 4 …
Metric Screw Thread Chart - Best Materials
www.bestmaterials.comMetric Screw Thread Chart Metric Tap Size Tap Drill (Inches) Clearance Drill (Inches) M1.6 x 0.35 #55 (0.052) #50 (0.070) M1.8 x 0.35 #53 (0.057) #48 (0.0.76)
Metric Tap and Clearance Drill Sizes - Data Metalcraft
www.datametal.comTap Drill Clearance Drill 75% Thread for Aluminum, Brass,& Plastics 50% Thread for Steel, Stainless,& Iron Close Fit Standard Fit M7 M6 M5 Screw Size (mm) Minor Diameter (mm) M2 M4 M18 M16 M10 M9 M8 M14 M20 53/64 22.0021.00 55/64
Metric Tap and Drill Chart - Industrial Metal Supply
www.industrialmetalsupply.comMetric Tap & Drill Chart METRIC THREAD SIZES Thread Size* Tap Drill Size** M1.6 x 0.35 1.25mm or #55 M2 x 0.4 1.60mm or #52 M2.5 x 0.45 2.05mm or #46 M3 x 0.5 2.50mm or #39 M3.5 x 0.6 2.90mm or #32 M4 x 0.7 3.30mm or #30 4.20mm or #19 M6 x 1 5.00mm or #8 M8 x 1.25 6.8mm or H M8 x 1 7.00mm or J M10 x 1.5 8.50mm or R M10 x 1.25 8.80mm or 11/32 ...
1970–2015 CATALOG - Whitney Tool
www.whitneytool.com- Tap Extensions to 1" NPT - Drill Extensions to 9/16" ... 1/8’’ LH Drill, 6’’ Extractor Extension and 5’’ Drill Extension 97177: S3 Includes EX3 Extractor, 3/16’’ LH Drill, 6’’ Extractor Extension and 5’’ Drill Extension ... M42 Metric Bolt Size Solid Pilot : Counterbore Set Six Piece Set of Metric Counterbores ...