LE MULTI-PANEL CLEARCOAT - axalta.com
Page 1 of 4 CROMAX® LE LE5100S™ MULTI-PANEL CLEARCOAT GENERAL DESCRIPTION A VOC compliant, two-component clearcoat designed for panel and multi-panel repairs in air dry and low bake …
Download LE MULTI-PANEL CLEARCOAT - axalta.com
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Advertisement
Documents from same domain
CHROMABASE BASECOAT - Axalta
www.axalta.com222S™ Midcoat Adhesion Promoter. Follow recommended flash times and then apply clearcoat over the entire panel. Tips for Success Tapering out each consecutive coat to melt the new color into the old color. For alternate blending techniques, refer …
Corlar® 2.1 ST™ Satin High Solids Epoxy Mastic
www.axalta.comCorlar 2.1 ST may also be used as a high performance tank lining primer on carbon steel or concrete for immersion service in near neutral pH water, fresh water, or saltwater. Corlar 2.1 ST is not recommended for use with potable water. Contact your Axalta representative for specific immersion service recommendations and procedures.
SelectSeal 0™ / 1™ / 422-52™ 2K Urethane Sealer - Axalta
www.axalta.comClean spray equipment as soon as possible with lacquer thinner or low VOC cleaner in VOC regulated markets. IMPORTANT NOTES 422-5X™ can be used under any Nason® topcoat If sealer dries overnight, scuff and recoat Do NOT apply directly over areas of bare metal DRY TIMES Allow at least 15 minutes flash time before applying topcoats.
CHROMASYSTEM™ MIDCOAT BASE 11000S™
www.axalta.comVOC REGULATED AREAS These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in the VOC Compliant Products Chart for your area. SAFETY AND HANDLING For industrial use only by professional, trained painters.
Ful-Poxy 491-16 DTM Epoxy Primer/Sealer - Axalta
www.axalta.comProperly sanded or blasted steel Properly cleaned or sanded aluminum, galvanized steel, or stainless steel Properly sanded SMC/fiberglass/body fillers/polyester putties TOPCOATS Any refinishing systems SURFACE PREPARATION Prior to sanding, remove all wax, grease, oil, and road tar with Nason® 441-05™
Steel, Resale, Primer, Epoxy, Galvanized, Galvanized steel, Dtm epoxy primer sealer
Ful-Thane 2K Urethane Binder (IB Quality)
www.axalta.comTechnical data sheet SAFETY AND HANDLING For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and SDS/MSDS precautions. If mixed with other components, mixture will have hazards of …
2030 Sustainability Goals - axalta.com
www.axalta.com2030 Sustainability Goals 80% of new technology and innovation developments will have a sustainability benefit 100% active global employees trained on Code of Business Conduct and Ethics 10% reduction of process waste, VOC emissions, and water use from operations (normalized to production) 50% absolute reduction of Scope 1
CHROMASYSTEM™ MIDCOAT …
www.axalta.comChromaPremier® Basecoat ChromaBase® Basecoat 222S™ Midcoat Adhesion Promoter Cromax® Pro Basecoat Cromax® Mosaic™ Cromax® EZ GUN SETUPS* HVLP: 1.3 mm-1.4 mm Compliant: 1.2 mm-1.3 mm . Page 2 of 4 AIR PRESSURE* HVLP: 8-9 psi at cap Compliant: 25-30 psi * Refer to the manufacturer’s directions for gun specific recommendations ...
Ful-Base Basecoat (IF Quality) - Axalta
www.axalta.comOEM basecoat/clearcoat finishes. The products referenced herein may not be sold in your market. Please consult your distributor for product availability. MIXING COMPONENTS Ful-Base® Basecoat IF Quality Ful-Base® 430-XX Tints Ful-Base® 435-93™ Basecoat Binder Ful-Base® 483-30™ Basecoat Activator Ful-Base® 441-2X™ Reducers *Do not use ...
Ful-Cryl II 2K Acrylic Enamel Topcoat (ID Quality) - Axalta
www.axalta.comPOT LIFE 4 hours at 70°F (21°C) SPRAY VISCOSITY 20-21 seconds in a Zahn #2 ADDITIVES Fisheyes Add 2-4 oz (60-120 ml) Nason® 495-01™ Fisheye Eliminator per RTS gallon, as needed. APPLICATION SUBSTRATES All OEM finishes, as well as properly prepared metal, fiberglass, plastic and fully cured previously painted surfaces. SURFACE PREPARATION
Related documents
MEGAPOSIT™ SPR™220 SERIES i-LINE PHOTORESISTS
microchem.comThe recommended softbake process for MEGAPOSIT SPR220 photoresist for films up to 4.0 μm is 115°C for 90 seconds on a contact hotplate. For films greater than 4.0 μm, use a
Recipes for Horlicks Lovers, from Horlicks Lovers
www.horlicks.co.ukAuthor: TINA LEE (Food Writer) Think homemade fudge is beyond you? Think again. These easy malty treats are delicious – and there won’t be a sugar thermometer in sight!
Published for customers of Hy-Vee Food Store, Marshall ...
www.marshallhyvee.com2 Hy-Vee Trader Published for Hy-Vee by the Marshall Independent FOR SALE: Live ducks & geese.Ph.829-6163. FOR SALE: 2003 Jayco Eagle, 33' 5th wheel camper, slide-out, sleeps 10, great family camper featuring a back bedroom with bunks and table. $8,500. Ph. 227-7057.
A Resource Guide for Planning and Operating Afterschool ...
www.sedl.orgA Resource Guide for Planning and Operating Afterschool Programs 3rd edition Compiled by Janet Hall Bagby
V O L U M E X X X I I I , I S S U E 1 2 D E C E M B E R 1 ...
www.swvmhi.dbhds.virginia.govV O L U M E X X X I I I , I S S U E 1 2 P A G E 4 Putting the Efficiency into Email – Meaningful Subject Lines Go beyond just “Hi” or “Hello.” The
Happy Thanksgiving!
www.careoptionsnetwork.org5 DATED EVENTS FOR MORE INFO: 651-793-2100 www.cerenityseniorcare.org Metro Agency on Aging will discuss recent changes in Medicare benefits and coverage,
Notification of Intent to Operate a Special Transitory ...
www.michigan.govRevised 10-31-2018 . Michigan Department of Agriculture & Rural Development (MDARD) Notification of Intent to Operate a . Special Transitory Food Unit (STFU)