Light-Emitting Diode (LED) Design Guide
been made in improving the efficiency, lumen output and performance of LED lights. The global LED lighting market is estimated to be $16B in 2012 and expected to reach nearly $40B by 2014 (Figure 1). The US market CAGR for commercial and outdoor LED lighting alone is expected to grow 26-30% through 2016.
Download Light-Emitting Diode (LED) Design Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
MOTOR PROTECTION TABLES - Circuit Protection, …
m.littelfuse.com2014 l por-ar ® p 2 motor protection guide motor protection tables motor s.f. = 1.15 or hp full load amps without overload relays with overload relays switch or s.f. = less
WHITE PAPER - Littelfuse
m.littelfuse.comTRANSFORMER PROTECTION WHITE PAPER The Importance of Effective Transformer and Control Transformer Protection
Application : Transient oltage uppressors (TVS iode ...
m.littelfuse.come: Transient oltage upressors (T iode pplications verview Litteluseco 2 © 2015 Littelfuse, Inc. Device Type Vulnerability (volts) VMOS 30-1800 MOSFET 100-200 GaAsFET ...
TMOV and iTMOV Varistor Series oHS - …
m.littelfuse.com© 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/14/17 Metal-Oxide Varistors (MOVs) Radial Lead Varistors …
WHITE PAPER - m.littelfuse.com
m.littelfuse.comTRANSFORMER PROTECTION WHITE PAPER The Importance of Effective Transformer and Control Transformer Protection
Light-Emitting Diode (LED) Design Guide - Littelfuse
m.littelfuse.comLight-Emitting Diode (LED) Design Guide Table of Contents Page Introduction 3-4 Safety and Reliability of LED Bulbs 5-7 Surge Immunity Requirements for Consumer LED Lighting/ Retrofit Lamps 8-10 Part Selection Matrix for LED Lamp Protection 11 ... duration of the test …
Selection Guide Fuse Characteristics, Terms and ...
m.littelfuse.comTypical PTC Circuit Protection Designs 11 Standards 12–14 PTC Selection Worksheet 15 Fuse and PTC Products Selection Guide 16–18 Packaging and Part Numbering 19 Legal Disclaimers 20 About this guide Fuses are current-sensitive devices that provide reliable protection for discrete components or circuits by melting under current overload ...
Automotive Circuit Protection using Littelfuse Automotive ...
m.littelfuse.com1.0 Mbits/s @ 40 meters 125 kbits/s @ 500 meters Cable Twisted or parallel pair wires, shielded or unshielded cable Termination Resistance 120 W resistors located at each end of the bus Min/Max Bus Voltage 12 V System: –3.0/+16 V
SM712 Series 600W Asymmetrical TVS Diode Array RoHS …
m.littelfuse.comlead-free • ESD, IEC 61000-4-2, ±30kV contact, ±30kV air ... • Communication Equipments Pinout and Functional Block Diagram Life Support Note: ... Capacitance vs. Reverse Bias 0 10 20 30 40 50 60 70 02468 10 12 80 Bias Voltage (V) Capacitance (pF) Clamping Voltage vs. I PP 0 5 10 15 20 25 30 35
MOTOR PROTECTION TABLES - Littelfuse
m.littelfuse.comampere rating motor running protection (used without properly sized overload relays) motor full-load amps back-up motor running protection (used with properly sized overload relays) motor full-load amps motor service factor of 1.15 or greater or with temp. rise not over 40°c. motor service factor less than 1.15 or
Related documents
LED Basics - College of Engineering - Purdue University
engineering.purdue.edumeasured in lumen and is the light power measured multiplied with the V-λ scaling function which compensates for the human eye’s sensitivity to different wavelengths. The luminous flux of LEDs is ... Each LED string is connected in parallel to the output of the SEPIC and in order to perform
BLT Series LED 2BLT4 - Acuity Brands
img.acuitybrands.comLumen Management: Unique lumen management system (option N80) provides on board intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of …
LLD & LED: Choosing the Right Light Loss Factor for LED ...
www.energy.govand lumen maintenance • Under existing prescribed methods, there is no way to differentiate between LED products • The IES-prescribed maximum LLD of 0.70 may be too conservative for some LED products, leading to excessive energy use • Using an alternative method may allow for greater energy-efficiency, as well as product competition
LED Color Characteristics - Energy
www.energy.govLED Color Characteristics Color quality is an important consideration when evaluating lighting products. This fact sheet reviews the fundamentals regarding light and color, summarizing the most important color issues related to white-light LED systems, including color consistency, stability, tuning, and rendering, as well as chromaticity.
LED Lighting Solutions - Florida Power & Light
www.fpl.comna or 6 3 99 3000k 7,823 b2-u0-g3 arb-b3-led-d1-t3-7030 g6 1 (20’), 2**, 5, 8 na or 6 3 99 4000k 8,451 b2-u0-g3 arb-b3-led-d1-t3-7040 g6 mesa 1 (20’), 2**, 5, 8, 9 na or 6 3 75/80 4000k 7,456 b2-u0-g2 pmm-e03-led-e-u-t3.ies e5 1 (20’), 2**, 5, 8, 9 na or 6 3 150/150 4000k 14,911 b3-u0-g3 pmm-e06-led-e-u-t3.ies j6 1 (20’), 2**, 5, 8, 9
Calculating Light Loss Factors - Energy
www1.eere.energy.govLED Sources L. p = time in hours to which the lumen output has degraded to a percent “p” of initial lumens L. 70. commonly used Use LM-80 report to help determine L. p. Note: LED lamps do not typically catastrophically fail. There lumen output degrades over time. This can be maintained through drive current control. 7
Energy Efficiency of LEDs
www1.eere.energy.govFigure 3 shows efficacy versus lumen output for more than 7,000 LED lamps and luminaires listed by LED Lighting Facts as of February 2013. For both integrated LED lamps and LED luminaires, the listed efficacy ranged from less than 10 lm/W to approximately 120 lm/W. A majority of products were between