LOCTITE 577™ - tdsna.henkel.com
TDS LOCTITE® 577™, August-2016 TYPICAL ENVIRONMENTAL RESISTANCE Cured for 1 week @ 22 °C Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m: M10 zinc phosphate steel nuts and bolts
Download LOCTITE 577™ - tdsna.henkel.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet LOCTITE 3621 - tdsna.henkel.com
tdsna.henkel.comThe information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of …
LOCTITE 243™ - tdsna.henkel.com
tdsna.henkel.comTDS LOCTITE® 243™, August-2016 For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush Loctite Material SpecificationLMS LMS dated June-29, 2009.
September-2016
tdsna.henkel.comTechnical Data Sheet LOCTITE 3220 September-2016 PRODUCT DESCRIPTION LOCTITE 3220 provides the following product characteristics: Technology Epoxy Appearance Black Product …
June-2016
tdsna.henkel.comTDS LOCTITE SI 5421, June-2016 Storage Store product in the unopened container in a dry location. Storage information may be indicated on the product container
October-2009 - tdsna.henkel.com
tdsna.henkel.comTDS LOCTITE® 222MS™, October-2009 % of Full Strength on Steel Cure Time 100 75 50 25 0 1min 5min10min 30min1h 3h 6h 24h 72h 0.05 mm 0.15 mm 0.2 mm Cure Speed vs. Temperature
LOCTITE 567™ - tdsna.henkel.com
tdsna.henkel.comTDS LOCTITE® 567™, October-2017 % of Full Strength on Steel Cure Time 100 75 50 25 0 0min 30min 1h 3h 6h 24h 72h 168h Zinc phosphate Stainless steel Zinc dichromate Black oxide
LOCTITE 680™ - tdsna.henkel.com
tdsna.henkel.comTDS LOCTITE® 680™, August-2016 according to ISO 10123. % of Full Strength on Steel Cure Time 100 75 50 25 0 30min 1h 3h 6h 24h 72h 168h 22 °C 5 °C Cure Speed vs. Activator
LOCTITE 567™ - Henkel
tdsna.henkel.comcompatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray with LOCTITE® SF 7471™ or LOCTITE® SF 7649™ and allow to dry. 3.
Technical Data Sheet LOCTITE STYCAST 2850FT
tdsna.henkel.comTDS LOCTITE STYCAST 2850FT, March-2015 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our
LOCTITE EA 9394 AERO 9-2013
tdsna.henkel.comLOCTITE EA 9394 AERO is qualified to MMM-A-132 Rev A, Type I, Class 3. The mechanical properties in this data sheet are also valid for LOCTITE EA 9394S AERO. LOCTITE EA 9394S AERO is only available in Semkits and differs from LOCTITE EA 9394 AERO as it has 1 part less thixotrope in the Part B to aid packaging.
Related documents
LOCTITE 567™ - tdsna.henkel.com
tdsna.henkel.comTDS LOCTITE® 567™, October-2017 % of Full Strength on Steel Cure Time 100 75 50 25 0 0min 30min 1h 3h 6h 24h 72h 168h Zinc phosphate Stainless steel Zinc dichromate Black oxide
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).