Magnetics - SMT power inductors - B82462G4
7 09/19 Cautions and warnings Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed.
Download Magnetics - SMT power inductors - B82462G4
Information
Domain:
Source:
Link to this page:
Documents from same domain
Film Capacitors - General technical information
www.tdk-electronics.tdk.comS Series resistance, due to contacts (leads, sprayed metal and film metallization) R P Parallel resistance, due to insulation resistance C Capacitance C, R S and L S are magnitudes that vary in the frequency domain (AC). R P is a magnitude defined in DC (insulation resistance). 2.2 Capacitance 2.2.1 Rated capacitance / measuring conditions
PTC thermistors, general technical information
www.tdk-electronics.tdk.com5.1.2 Rated resistance RR The rated resistance RR is the resistance value at temperature TR.PTC thermistors are classified according to this resistance value. The temperature TR is 25 °C, unless otherwise specified. 5.1.3 Minimum resistance Rmin The beginning of the temperature range with a positive temperature coefficient is specified by the
Aluminum Electrolytic Capacitors - TDK Electronics
www.tdk-electronics.tdk.comStructure of anode foil for low-voltage capacitors (magnification 400x) The dielectric layer of an aluminum electrolytic capacitor is created by anodic oxidation (forming) to build up an aluminum oxide layer on the foil. The layer thickness increases in proportion to the
Ferrites and accessories - TDK Electronics
www.tdk-electronics.tdk.comPeak value of flux density deviation DC magnetic flux density Remanent flux density Saturation magnetization Winding capacitance Core distortion factor Relative disaccommodation coefficient DF = d/Pi Disaccommodation coefficient Activation energy Frequency Cut-off frequency
Film Capacitors - Metallized Polypropylene Film Capacitors ...
www.tdk-electronics.tdk.comMetallized polypropylene film capacitors (MKP) B32651 ... B32658 High pulse (wound) Please read Cautions and warningsand Page2of61 Important notesat the end of this document. Dimensional drawings Number of wires Lead spacing ±0.4 Lead diameter d 1 ±0.05 Type Drawing 2-pin 10 0.6 B32651 A1
NTC thermistors, application notes - TDK Electronics
www.tdk-electronics.tdk.comNTC thermistors exhibit a distinctly non-linear R/T characteristic. If a fairly linear curve is required for measurements over a (wide) temperature range, e.g. for a scale, series-connected or paral-leled resistors are quite useful. The temperature range to …
SIOV metal oxide varistors - TDK Electronics
www.tdk-electronics.tdk.comLeaded varistors B722* StandarD series Please read Cautions and warnings and Page 6 of 47 Important notes at the end of this document. Electrical specifications and ordering codes Maximum ratings (TA = 105 ... SIOV metal oxide varistors, leaded varistors, StandarD series
Related documents
CuSn6 - Aurubis Stolberg
www.aurubis-stolberg.comWerkstoff Datenblatt CuSn6 Korrosions-beständigkeit Verwendung Automotive, Bauteile der Elektrotechnik, Steckverbinder, Relais, Federkontakte, Federn, Metallschläuche, Buchsen, Papier-, Textil- und chemische Industrie sowie der allgemeine
热加工行业论坛 www.rjghome.com 各国铜牌号及标准对照表
www.materials.cn热加工行业论坛 www.rjghome.com 各国铜牌号及标准对照表 中国 德国 欧洲 国际标准 美国 日本
von Metallen und Legierungen (Mittelwerte) l1 = l0(1+a(t1 ...
www.burdeco.comWärmeausdehnung von Metallen und Legierungen (Mittelwerte) Längenausdehnung l 1 = l 0(1+a(t 1-t 0) l 1 = Länge bei t 1 Grad C, l 0 = Ausgangslänge bei t 0 Grad C a = Längenausdehnungszahl, ist die Verlängerung der Längeneinheit bei 1 Grad Temperaturerhöhung (zwischen 0 bis 100 Grad C) Metall, Legierung a x 10-6 Metall, Legierung a x 10
CuSn8 - herrmann-buntmetall.de
www.herrmann-buntmetall.de3.1.1.2 Federbänder nach DIN 1777 Werte gelten für Federbänder mit Dicken s von 0,1 bis 1,0 mm. Zustand Kurzzeichen Anhänge- Vickershärte Federbiege- Kleinster Radius des Biegestempels für 90"-Abkantung 0.20/0-Dehngrcnze2)
CuSn6 - kupferinstitut.de
www.kupferinstitut.deCuSn6 4 I Deutsches Kupferinstitut 4.1.2 Federbänder - nach DIN EN 1654 - Zustand Zugfestigkeit 0,2 %-Dehngrenze Bruchdehnung Härte für Dicken von 0,1 bis 0,25 mm