Master Products Catalog - Gates Corporation

Industrial Hose, Couplings and Equipment Catalog

TERMS POLICY Terms are 2%, 30 days. Discount may be earned if paid on or prior to the 30th day following the invoice date. CONDITIONS › Prices do not include charges for special packaging, which will be extra, unless otherwise specified.

BELT I.D. CHART - Gates Corporation

SYNCHRO-POWER™ POLYURETHANE BELTS Example: T5-270-8 Synchro-Power Belts A T2.5 2.5mm.098 in. T5 5mm.197 in. T10 10mm.394 in. AT5 A5mm.197 in. AT10 10mm.394 in. DT5 5mm.197 in. DT10 10mm.394 in. A 270H075U Synchro-Power Timing Belts A MXL 2.03mm.080 in. XL 5.08mm.200 in. L 9.53mm.374 in. H 12.70mm.500 in. A POLY CHAIN & …

  Corporation, Gate, Belt, Gates corporation

PC 707 Crimper - Gates Corporation

the crimp OD. Insert the coupling into the die set approximately 1/8” below top of die. (See Photo 1.) Slide the die cone assembly under the ram until it stops against back locating pins and push the crimp button and hold. Release the button immediately when the pump stops. Remover coupling and measure crimp diameter, which

  Corporation, Gate, Crimp, Gates corporation

DRIVE DESIGN MANUAL - Gates Corporation

Standard belt sizes are listed in the stock Poly Chain GT Carbon Belt Tables on page 3. Specifications for the 8mm and 14mm pitch belts list the belt pitch lengths, number of teeth, stock widths and appropriate weights. Using the information from these tables, a code for ordering a specific belt can be determined as shown in the following examples:

  Table, Corporation, Gate, Belt, Gates corporation, Belt tables

Gates Powersports Recreational Belt Applications

Gates 1144 15th Street, Suite 1400 Denver, CO 80202, U.S.A. 303.744.1911 POWERSPORT RECREATIONAL BELT APPLICATIONS WEATHERLY NO. 400 CATALOG NO. 431-2070

  Applications, Recreational, Belt, Recreational belt applications

Timing Belt Replacement Interval Guide - Gates Corporation

Today, Gates is the world’s largest manufacturer of Timing Belts and Timing Component Kits (TCKs). Import or Domestic, if there is a car in the U.S. with a timing belt in it, we have the replacement part for it. As the OE or OES supplier for virtual every vehicle manufacturer worldwide, you can be confident every time you install Gates.

  Guide, Vehicle, Replacement, Corporation, Gate, Belt, Timing, Interval, Timing belt replacement interval guide, Gates corporation

NIGP Commodity Codes (18th Edition)

ABRASIVES: 005-05-00 Abrasive Equipment and Tools : 005-14-00 Abrasives, Coated: Cloth, Fiber, Sandpaper, etc. 005-14-02 ABRASIVE BRISTLE BRUSHES, DISC SHAPED

  Code, Commodity, Nigp, Nigp commodity codes

Electrical metallic tubing (EMT) fittings

ELECTRICAL METALLIC TUBING (EMT) FITTINGS B81 EMT fittings – Nylon insulated Cat. no. Size (in.) Dimensions (in.) A B Diagram Across 1 corners A B 5123 1⁄2 13⁄64 121⁄32 5223 3⁄4 121⁄64 127⁄32 5323 111⁄16 7⁄8 5423 1 1⁄4 2⁄16 211⁄32 5523 11⁄2 25⁄16 223⁄32 5623 2 225⁄32 213⁄16 UL Listed and CSA Certified concrete-tight

  Nylon, Tubing

TRP PARTS CATALOG - BELTS & HOSES CHAPTER

TABLE OF CONTENTS Belts & Hoses Choosing the right replacement part or service for your vehicle—whether you own one, or a fleet—is one of the most important decisions you can make for your business. And, with tested TRP® parts it’s an easy decision. Regardless of the make you drive, TRP® quality replacement parts are engineered to fit ...

Antenna Here is a Dipole - ARRL - Home

Within limits, however, resonance isn't necessary for a dipole to be effective, as I'll explain a bit later. Resonant half-wave dipoles range in size from about 16 feet for the 10-meter band (28-29.7 MHz) to 260 feet for the 160-meter band (1.8-2 MHz). See Table 1. The lowest frequency at which a dipole is resonant is known as its fundamental

  Here, Antenna, Dipoles, Antenna here is a dipole

Homebrew Your Own Inductors! - ARRL - Home

Can’t find the inductors you need for an antenna, a tuner or amplifier? Build your own—it’s easy! By Robert H. Johns, W3JIP Air-dielectric inductors can be made quite easily at home. Some coils are held together by clear epoxy ribs, others use scrap pieces of PC board and epoxy. The larger coils are made from 1/4-inch-diameter copper tubing.

  Tubing

One-touch Fittings Series KQ2

Accepts nylon, and urethane tubes. Has large retaining force. Collet Guide Series KQ2: Light gray Series KQ : Blue Small disconnecting force. When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube excessively. Release button Effective when piping in a confined space.

  Nylon, Tubing

2021-2022 Legal and Illegal Parts List - FIRST

T-Slot Aluminum Extruded aluminum pieces from various manufacturers such as 80-20, McMaster-Carr, Macron, etc. All fasteners and compatible hardware are allowed MISC (No Images Available) • Material strictly used for Light Sensor color filter. • Hook and loop - Velcro, 3M Dual Lock. (May not be used as tape).

Owner’s Manual with Parts List - ingersollrand

22204929 Revision B May 2015 Save These Instructions SS3L3 Owner’s Manual with Parts List EN Owner’s Manual With Parts List ES Manual del propietario con la lista de piezas FR Manuel du propriétaire avec liste des pièces 62215.10.56

One-touch Fittings Series KQ2 - SMC Pneumatics

Note 1) Soft nylon tubing is not compatible with water. Made to Order (Refer to page 58 for details.) 39 One-touch Fitting Series KQ2 K M H KK D MS LQ MQR T P0018-P0075-E.qxd 08.8.27 4:40 PM Page 39. Hex. socket head male connector KQ2S P. 42 Male connector KQ2H P. 42 Universal male elbow

  Fitting, Touch, Nylon, Tubing, One touch fittings, Nylon tubing

FITTING and TUBING

4.b FITTINGS & TUBING TUBING SERIES PAGE NUMBER TS, TISA 4.30 SOFT NYLON TUBING TU, TIUB 4.30 POLYURETHANE TUBING TFU 4.31 POLYURETHANE FLAT TUBING TCU 4.31 POLYURETHANE COIL TUBING TM 4.32 MULTITUBE HOLDER TK 4.32 TUBE CUTTER Courtesy of Steven Engineering, Inc. 230 R ! yan Way, South San Francisco, CA …

  Nylon, Tubing, Tubing tubing, Nylon tubing