MSMA 6 Plus - CDMS
MIXING INSTRUCTIONS This product is completely water-soluble. Fill the spray equipment reservoir about half full with water and add the required amount of herbicide with agitation. Finish filling the tank with water and apply. After use, clean equipment thoroughly by flushing with water. Do not store spray solution in tank for a prolonged period.
Download MSMA 6 Plus - CDMS
Information
Domain:
Source:
Link to this page:
Documents from same domain
RESTRICTED USE PESTICIDE - cdms.net
www.cdms.netFIFRA Section 24(c) Special Local Need FOR DISTRIBUTION AND USE ONLY IN THE STATE OF NORTH DAKOTA RESTRICTED USE PESTICIDE For retail sale to and use ONLY by Certified Applicators or person under their direct supervision and …
FOR USE IN SELECTED CROPS - CDMS Home
www.cdms.net† If applied by air, leave an untreated buffer zone of 170 feet. Must use straight-stream nozzles (D-6 or larg-er); wind can be no more than 8 mph; and release height
FIFRA Section 24(c) Special Local Need FOR …
www.cdms.netFIFRA Section 24(c) Special Local Need FOR DISTRIBUTION AND USE ONLY IN THE STATE OF INDIANA RESTRICTED USE PESTICIDE For retail sale to and use only by Certified Applicators or persons under their direct supervision and only for uses covered
Specimen Label User Safety Recommendations - …
www.cdms.net2 Specimen Label Revised 01-05-17 Storage and Disposal Do not contaminate water, food, feed or seed by storage or disposal Pesticide Storage: Store above 10°F (-12°C) to keep product from
SAFETY DATA SHEET - CDMS
www.cdms.netProduct name : RODEO Herbicide Issue Date: 11/10/2015 Page 3 of 11 Unusual Fire and Explosion Hazards: This material will not burn until the water has evaporated. ...
Parallel - CDMS
www.cdms.net4 AGRICULTURAL USE REQUIREMENTS Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170 . …
RESTRICTED USE PESTICIDE
www.cdms.netHave the product container or labe l with you when calling a poison co nt r oce d - tor,s or going for treat ment. You may also contact 1-(800) -3148 fo rE eg ncy
RESTRICTED USE PESTICIDE - CDMS Home
www.cdms.net3 maintained at 110% that of the largest pesticide container or application equipment used on the pad and have sufficient capacity to contain all product spills, equipment
GLYSTAR PLUS SAFETY DATA SHEET Page 1 6 …
www.cdms.netglystar plus safety data sheet page 1 of 6 section 1 - chemical product and company identification company address: albaugh, llc ankeny, ia 50021 1-800-247-8013 emergency telephone numbers:
DuPont Aproach Prima - CDMS
www.cdms.netPRODUCT INFORMATION DuPont™ APROACH® PRIMA is a broad-spectrum fungicide for control of foliar plant diseases and has preventive, curative, and systemic activity.
Related documents
Rosemount 5408 and 5408:SIS Level Transmitters
www.emerson.comThe Rosemount 5408 is ideal for the most challenging applications, including reactors where there can be agitation, foaming, and condensation, as well as high temperatures and pressures. Blenders and mixers The Rosemount 5408 can help you withstand the rigors of blenders and mixing tanks. Easy to install and commission, it is also
Importance, Objectives & Factors Affecting Dissolution ...
pharmaquest.weebly.comFor erodible tablet speed of agitation is bit high because it requires external force. ... depend to a large extent on mixing time of drug/excipient preblende. With lubricant. On other hand, disintegrants with strong swelling capacity such as sodium starch glycolate were hardly affected by mixing time with lubricant. ...
The Composting Process - USU
extension.usu.edufront-end loader, or by means of mechanical agitation with a special compost turner. 2. C:N Ratio Carbon (C), nitrogen (N), phosphorous (P), and potassium (K) are the primary nutrients required by the microorganisms invol-ved in composting. Microorganisms use carbon for both energy and growth, while nitrogen is essential for protein pro-
Wet Etching - UWEE
labs.ece.uw.eduR. B. Darling / EE-527 / Winter 2013 Etch Selectivity • The selectivity of an etch is the ratio of the etch rate for the material it is desired to remove versus the etch rate for some other material that it