Multi-Application Peripherals
Mounting Plate Sheet metal, galvanized Temperature Range 32° to 120° F (0° to 49° C), intended for indoor operation Humidity Range Up to 93% RH at 100° F (38° C) Installation Instructions 574-184 Multi-Application Peripherals UL, ULC, CSFM Listed; FM Approved; IDNet Communicating Devices MEA (NYC) Acceptance* Model 4090-9002 Relay IAM
Download Multi-Application Peripherals
Information
Domain:
Source:
Link to this page:
Documents from same domain
System Accessories - Simplex Fire
simplex-fire.comMechanical Dimensions 10-3/8 ... System Accessories UL, CSFM Listed* Remote Station Devices, ... to RJ31X jacks, requires 2, 2080-9022 cables Simplex Fire Alarm ...
Fire Control Panels - Simplex Fire
simplex-fire.comFeatures Simplex® 4100ES Box and door options: Boxes are available sized for one, two, or three equipment bays, each with a battery bay located at the bottom ...
Fire Control Panels - Simplex Fire
simplex-fire.comTypical use is when the host fire alarm control panel is located away from the area where those responding to a fire situation need status information. Status and Control. ... Fire Control Panels UL, ULC, CSFM Listed; FM Approved; Remote Annunciator Panels MEA (NYC) Acceptance* S4100-0038-14 5/2018.
Fire Control Panels - Simplex Fire
simplex-fire.comSeries fire alarm control panel equipment with 4100ES Series products using the existing backbox: Retrofit kits include either a solid or glass-fronted metal door, retainer panels for glass door applications, and box extension hardware Kits are available for 1, 2, or 3 bay 4100ES equipment
System Accessories, LCD Annunciators - Simplex Fire
simplex-fire.comFeatures Remote LCD annunciator for use with Simplex® model: 4100ES and 4100U fire alarm control panels Legacy products 4100, 4120, and 4020 fire alarm control
4010ES Fire Alarm Control Panel
simplex-fire.com• Ethernet connectivity options include Building Network Interface Module (BNIC), SafeLINC Internet Interface, and BACpac Ethernet Portal • Dual Class A IDNAC Isolator (DCAI) • Dual RS-232 Module • VESDA Air Aspiration High Level Interface • Serial DACT • 8 Zone IDC Modules Class A or B • 4 Point Auxiliary Relay Module
MAPNET II Communicating Devices - simplex-fire.com
simplex-fire.comsuch as elevator capture, HVAC control, pressurization fan control, and damper control. The control relay provides a DPDT contact (contact ratings are shown on page 4). General Specifications Communications Supplied by MAPNET II, 24 to 40 VDC with data Power Separate 24 VDC required from listed fire alarm power supply Wiring Information
4007ES Fire Detection and Control with Addressable ...
simplex-fire.com4007ES Fire Detection and Control with Addressable Initiation and Addressable Notification * This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. ... TrueAlarm analog sensor to provide a single multiple sensing assembly using one system address. The CO ...
4100ES Addressable Fire Detection and Control Emergency ...
simplex-fire.com4100ES Addressable Fire Detection and Control Emergency Voice/Alarm Communications Equipment * This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. ... Analog audio control modules are for systems that require one or two simultaneous channels of audio ...
4007ES Fire Control Panels
simplex-fire.comRecorder Co. are the property of Tyco Fire Protection Products. 4007ES Fire Control Panels UL, ULC, CSFM Listed; Fire Detection and Control with Addressable FM, NYC Fire Dept Approved* Initiation and Addressable Notification S4007-0002-10 1/2017
Related documents
Handbook of STEEL SIZES & WEIGHTS
www.coyotesteel.comCoyote Steel & Co. 2030 Cross Street Eugene, Oregon 97402 USA No. 1 Handbook of STEEL SIZES & WEIGHTS For Industry Phone: 541-461-2060 Toll-free: 1-800-553-0240
ZINC COATINGS - American Galvanizers Association
galvanizeit.orgContinuous sheet galvanizing is also a hot-dip process, but is only applied to steel sheet, strip, and wire. A coil to coil process, steel sheet from 0.010 to 1.70 inches (0.25 mm to 4.30 mm) thick and up to 72 inches (1,830 mm) wide is passed as a continuous ribbon through cleaning baths and molten zinc at speeds up to 600 feet per minute.
TECHNICAL DATA SHEET - Henry
henry.comexterior-grade gypsum sheathing, plywood, OSB, precast or cast-in-place concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum and galvanized metal. Strike masonry joints flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions.
TECHNICAL DATA SHEET - Henry
henry.comcast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing
DATE: LOCATION: TYPE: PROJECT: LE Series CATALOG
hubbellcdn.comstroke. Rough-in kit: galvanized steel, .036 (20 Ga.) housing, .060 (16 Ga.) mounting bars INSTALLATION • Universal rough-in box accommodates recessed installation of all models in wall, ceiling or end-mount applications • All mounting hardware is fully concealed CATALOG #: RELATED PRODUCTS LES Replacement battery - 0120894 KEY DATA
Ful-Poxy 491-16 DTM Epoxy Primer/Sealer - Axalta
www.axalta.comProperly sanded or blasted steel Properly cleaned or sanded aluminum, galvanized steel, or stainless steel Properly sanded SMC/fiberglass/body fillers/polyester putties TOPCOATS Any refinishing systems SURFACE PREPARATION Prior to sanding, remove all wax, grease, oil, and road tar with Nason® 441-05™
Hot dip galvanized coatings on fabricated iron and steel ...
www.galvanizeit.coma) sheet, wire and woven or welded mesh products that are continuously hot dip galvanized; b) tube and pipe that are hot dip galvanized in automatic plants; c) hot dip galvanized products (e.g. fasteners) for which specific standards exist and which might include
SDI MANUAL OF CONSTRUCTION WITH STEEL DECK
www.sdi.org1. General - All Deck Products Steel deck is made by cold forming structural grade sheet steel into a repeating pattern of parallel ribs. The strength and stiffness of the panels are a result of the shape of the ribs and the mate-rial properties of the steel. Deck lengths can be varied to suit job