NIGP Commodity Codes (18th Edition)
005-14-23 cloths, abrasive, metal: 005-14-26 cloths, abrasive, silicon coated: 005-14-27 cloths, abrasive: 005-14-30 discs, abrasive, fiber combination backing, type a, aluminum oxide closed coating: 005-14-31 discs, abrasive, paper backing: 005-14-32 discs, abrasive, (including quick-lok types) 005-14-33 discs, abrasive, aluminum oxide
Download NIGP Commodity Codes (18th Edition)
Information
Domain:
Source:
Link to this page:
Documents from same domain
STATEMENT OF WORK FOR PRINTER/COPIER MAINTENANCE …
app.ocp.dc.govPrinter/Copier Maintenance and Support Services 2 STATEMENT OF WORK FOR ... Printer/Copier Maintenance and Support Services 3 POC Point of Contact. Person designated by the COTR to initiate requests for ... paper and toner cartridges consumed in printer/copier output. Includes delivery to each site of paper, ribbons and ink/toner modules and ...
Related documents
MIL-A-8625F Anodic Coatings, for Aluminum and Aluminum ...
www.coastlinemetalfinishing.comANSI/ASTM B 137 - Weight of Coating on Anodically Coated Aluminum, Measurement of ASTM B 244 - Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy Current Instruments, Measurement of ASTM D 822 - Light and Water Exposure Apparatus (Carbon-Arc
UNIT 4 METAL COATING PROCESSES Metal Coating …
www.ignou.ac.inUNIT 4 METAL COATING PROCESSES Metal Coating Processes Structure 4.1 Introduction ... formation of an oxide/sulphide layer. To avoid this a layer of some barrier metal ... of thickness 10 µm over nickel plating is done on steels. It is used in case of metal furniture, automotive trims, etc. Chromium plating is a hard plating providing ...
ZINC COATINGS - American Galvanizers Association
galvanizeit.orgrequirements based on steel type and thickness. The Time to First Maintenance Chart shows the Figure 5 linear relationship between zinc coating thickness and maintenance-free service life. For example, according to ASTM A123, structural steel greater than or equal to ¼ inch thick has a minimum coating requirement of
Intertherm 228HS - AkzoNobel
international.brand.akzonobel.comOct 12, 2015 · Ensure surface is clean, dry and free from metal corrosion products prior to coating. Light sweep with non-metallic and chloride free abrasive (e.g. aluminium oxide or garnet) to obtain anchor profile of approximately 50 microns (2 mils). SURFACE PREPARATION Material is supplied in two containers as a unit. Always mix a complete unit in the
Device Fabrication Technology1 - Chenming Hu
www.chu.berkeley.eduthe metal-oxide-semiconductor transistor, the subject of Chapters 5–7. SiO2 layers of precisely controlled thickness are produced during IC fabrication by reacting Si with either oxygen gas or water vapor at an elevated temperature. In either case …
TIN MILL PRODUCTS
www.jfe-steel.co.jpTin Coating Mass Designation of Standard Tin Coating Mass (g/m2) Equally Coated 2.8 5.6 8.4 11.2 Diffrentially Coated 2.8/5.6 2.8/8.4 2.8/11.2 5.6/8.4 5.6/11.2 8.4/11.2 The tin coating mass is changed depending on usage. In case of heavier tin coating mass, it is applied to high corossion contents and to non painting can in general. On the other
Adhesion of Aluminium Foil to Coatings – Stick With it
www.tappi.orgOxide thickness, annealed ... metal surface and the coating. Such oxide growth is due to the foils reaction with oxygen and/or humidity present in the headspace of packages. With regard to dairy products, the 1%-content of lactic acid in a yoghurt, for example, can attack the metal if the lacquer carries pinholes. An
Handbook for Corrosion Protection - Teknos
www.teknos.comanode site is the metal surface’s less noble site or a site with a higher surface energy. Image 1.1 illustrates the formation of local pairs onto a metal surface, and the anode and cathode reactions. Image 1.1 The formation of local pairs onto a metal surface, and the anode and cathode reactions. Local corrosion pairs (-) anode Fe –> Fe2+ + 2e-