NMRA DCC Reference Manual - Q.S.Industries
NMRA DCC Reference Manual For QSI Quantum® 3, 2, and 1 Equipped Locomotives Version 5.2.0 For Firmware Versions 7, 8 and 9 5-August-2015
Download NMRA DCC Reference Manual - Q.S.Industries
Information
Domain:
Source:
Link to this page:
Documents from same domain
QSI Quantum HO Equipped Locomotives - …
qsindustries.comDC Analog Reference Manual for QSI Quantum® HO Equipped Locomotives Version 4.0 For Firmware Version 7 25 August 2006
Related documents
TRACKWORK doing it right - Scenic Express
www.scenicexpress.com• NMRA dimensions. The data in the table below are for HO scale based on the standard dimensions in NMRA RP-12.3. Manufacturers of model railroad turnouts sometimes make the lead length shorter and thus the closure radius smaller than these standard dimensions. Turnout Lead Frog Closure Number Length Angle Radius #4 5.06” 14° 15’ 15”
BETRIEBSANLEITUNG Neu - ZIMO
www.zimo.atAlle Decoder Familien sind im NMRA-DCC-Datenformat und auch im Gleichstrom-Analogbetrieb (DC, Modellbahn-Trafos, PWM- und Labornetzgeräte) einsetzbar. Manche Decoder Familien unterstüt-zen auch MOTOROLA (MM) und auch den Wechselstrom-Analogbetrieb (AC, Trafos mit …
CV Liste Expertensuche Stand : Februar 2020
www.zimo.atDCC – Signal (Methode Lenz „ABC“) Asymmetrie. Siehe auch CV #134! 0,1,2,3 0 Aktivierung des autom. positionsabhängigen Anhaltens durch „asymmetrisches DCC-Signal“ (Lenz „ABC“). = 1: Anhalten erfolgt, wenn die rechte Schiene (in Fahrtrichtung) eine höhere Spannung als die linke Schiene aufweist.
DCC Wiring - Pacific Northwest Region of the NMRA
4dpnr.comDCC WIRING CLINIC 25 Summary DCC wiring is different from DC blocks and cab control in consideration of wiring methods, but many of the same basic rules for electrical gaps etc. still apply. Higher currents = heavier power wiring, and overload protection must work. DCC wiring is simpler, but intolerant of sloppy workmanship
FINE TUNING LOCOMOTIVE SPEED - DCC
cmrci.infoFINE TUNING LOCOMOTIVE SPEED - DCC ... NMRA specifies a default setting equivalent to 0.032 seconds per speed step in 28 step mode. Entering a value of 1 means the loco would reach full speed in just under a second. A value of 10 increases this delay to 0.32
Ladder Track System Turnouts - Micro Engineering
microengineering.comthe minimum track spacing of 2-1/16 inch (the NMRA standard) between body tracks. The amount of increased yard area is dependent on the type of yard modeled (yard configuration) and the size of the yard. Generally the larger the yard, the more space gained. Through TrackDiverging Track Point End #5b #5c #5d #5e #5a Frog End Ladder Track System ...
Western Pacific*
www.athearn.com• Onboard Tsunami2 DCC/Sound decoder • Dual cube speakers for optimal sound quality • Sound units operate in both DC and DCC • Engine, horn, and bell sounds work in DC • Some functions are limited in DC • All functions NMRA compatible in DCC mode
Quick Start Guide - Bachmann Industries
www.bachmanntrains.comthe nmra dcc standards and recommended practices. created date: 3/20/2012 12:00:51 pm ...
Spectrum DCC Quick Start Guide - Bachmann Trains
www.bachmanntrains.comTHE NMRA DCC STANDARDS AND RECOMMENDED PRACTICES For service/repair, contact the Bachmann Service Department at 1-800-356-3910 or via e-mail at service@ bachmanntrains.com. Bachmann’s Service Department is available Monday thru …
DCC Decoder Default Resets
www.nmra.orgSince the factory reset is not in the NMRA DCC standards or recommended practices, each manufac-turer can do their own thing. If you do not know the manufacturer of your decoder, you can try reading CV8 on the program track. This is a read only CV that has the manufacturer’s ID number (numbers are shown in decimal)