OPERATING INSTRUCTIONS 4 Function, 15 Range Digital …
4 Function, 15 Range Digital Multi-Meter GDT-3190 1.1 FUNCTIONS (Figure 1) 1. 2000 count digital display 2. 15 Position Function/Range Dial 3. AC Volts 4. DC Volts 5. Resistance 6. Battery Test 7. Off Dial Selection 8. Low Battery Indicator 9. Common Input Jack 10. Positive Input Jack 11. Protective Rubber Boot and Tilt-Out Stand 1.1 METER ...
Download OPERATING INSTRUCTIONS 4 Function, 15 Range Digital …
Information
Domain:
Source:
Link to this page:
Documents from same domain
Analog Multimeter Multímetro análoga Multimètre …
file.ecmindustries.comtest leads meeting ETL, cETL, CE CAT II 500V IA can be used in this multimeter. 6) Discharge a capacitor before measuring it. 7) Remove the test leads from the circuit being measured as soon as the test is completed. 8) Do not measure voltage when the function/range switch is set on the resistance (ohms) or the current (mA) settings.
Related documents
Electrical Circuits Sample - Lesson 6 - Science Companion
www.sciencecompanion.comTo make tester with. Classroom Supplies. Conductors. 4 per group For students to test. Place in a resealable plastic bag with four insulators. See step 2 in preparation. Electrical tape. 2 pieces per group To secure wires to D-cell batteries. Insulators. 4 per group For students to test. Place in a resealable plastic bag with four insulators ...
The A-Z of apprenticeships - GOV.UK
assets.publishing.service.gov.ukThe A-Z of apprenticeships Creative and design l e ev L Assistant technical director (visual effects) 4 Bespoke Saddler 3 Bespoke tailor and cutter 5 Broadcast and media systems engineer 6 Broadcast production assistant 3 Creative Venue Technician 3 Junior 2D artist (visual effects) 4 Junior content producer 3 Junior journalist 3 Leather craftsperson 2 Live event rigger 3
PRODUCT MANUAL FOR a.c. STATIC DIRECT CONNECTED …
bis.gov.inImpulse Voltage Tester 3 Insulation Tester 4 Test bench load with phantom system, Reference Standard Meter Accuracy requirements Cl.6.12 5 Power Meter Power Consumption Cl.6.10.1 6 Voltage Dips and Interruption Tester Influence of supply voltage Cl.6.10.2 7 Short time overcurrent tester Influence of Short-time overcurrents Cl.6.10.3 8
Table of Contents
csr.innova.comInspect the digital multimeter for damage to the case. Do not use if cracked, distorted, excessively dirty or any abnormal condition exists. Inspect the test leads for damage. Check for cracked insulation, broken or damaged probes, loose or bent probe pins. Do not use if any abnormal condition exists.
3300 Multimeter English SinglePage New
csr.innova.com• This Digital Multimeter is intended for INDOOR USE ONLY. ... To prevent electrical shock and/or damage to the tester or the equipment under test, observe the following safety precautions: ... † Equipment marked is protected throughout by Double or Reinforced Insulation. † Operating environment: Temperature - 32° to 104° F. (0° C to ...
Operation, & Maintenance Manual
franklinwater.com• Disconnect all motor leads from VFD before checking the motor insulation with Megger tester. The Megger tester 1000VDC output can damage the VFD power components. • Refer to Chapter 8 for periodic inspection and parts replacement details. (7) Disposal • Dispose of VFD properly as an industrial equipment wastes.
V7X SERIES OPERATING & MAINTENAN E MANUAL
vitrek.como Meets UL, CSA, IEC Safety Tester Requirements o CE Safety Mark Certified to EN61010 Equally at home in simple and complex systems o USB 2.0, Serial RS232 and Digital I/O Interfaces are Standard o Able to be used in Complex Multi-Point Scanning Systems
Tooling Guide for Aerospace Wiring Systems
www.farnell.combest Digital Tensile Testers to further meet the demand for fewer sources and improved support through a wider range of user needs. The MPT-250B Motorized Wire Crimp Pull Tester is ideal when a constant rate of pull is desired. It tests crimp strength on terminations up to size 8