Process Interface Valves - Swagelok
CHECK & RELIEF VALVES NEEDLE & VALVES METERING REGULATORS & FILTERS PROCESS INTEFACE VALVES MEASUREMENT DEVICES REFERENCES MEDIUM- HIGH- PRESSURE TUBE FITTINGS Process Interface Valves Double Block and Bleed (DBB) Valves ... 0 .16 to 0 .24 (4 to 6) ...
Download Process Interface Valves - Swagelok
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
Automatic Control Valves - Watts
media.wattswater.comControl Valves at affordable prices. Our fusion bonded, epoxy coated, ductile iron Automatic Control Valves offer long life and minimal maintenance. And for harsh applica-tions and environments, our Fabricated Stainless Steel Valves provide a cost effective solution. Whether your application requires Pressure, Level, Pump, or Flow
INSTALLATION INSTRUCTIONS - Lennox
resources.lennox.comwith pressures of 0 − 800 psig on the high side and a low side of 30" vacuum to 250 psig with dampened speed to 500 psi. Gauge hoses must be rated for use at up to 800 psig of pressure with a 4000 psig burst rating. OPERATING SERVICE VALVES The liquid and vapor line service valves are used for removing refrigerant, flushing, leak testing ...
LV LOADER DIRECTIONAL CONTROL VALVES …
www.brand-hyd.comRelief Adjustment – Relief setting is factory preset to 2000 psi, unless otherwise noted within model code. Relief valve ... Painting valves is acceptable as long as the following precautions are taken: ... 0.0 0.7 1.4 2.1 2.8 3.4 4.1 4.8 5.5 6.2 6.9 3.8 7.6 11.4 15.118.9 22.7 26.5 30.3 34.1 37.9 0 10 20 30 40 50 60 70 80 90 100
Medium- and High-Pressure Fittings, Tubing, Valves, and ...
www.swagelok.comRelief Valves Tubing Up to 60 000 (4134) Applications Medium- and high-pressure fittings, valves, and components are designed to meet requirements of demanding applications such as the following: Oil and gas Alternative fuel industry infrastructure ... 3/8 0.134 15 000 ...