Process Interface Valves - Swagelok
Double block and bleed isolation Vents and drains Extreme service Over 100 000 double block and bleed and monoflange valves installed. “The valves are reliable and they last” “We have made Swagelok double block and bleed’s our standard and will be adding more during our next shutdown” 26 in . (66 .0 cm) 10 in . (25 .4 cm) 7 in .
Download Process Interface Valves - Swagelok
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
Double Block and Bleed Valves - Bonney Forge Corporation
bonneyforge.comprovide the exact Double Block & Bleed valves and actuators to meet the most demanding application requirements. Our Double Block & Bleed valves are available in an extensive range of designs, materials, sizes and pressure classes and are in full con-formance with ASME, API and NACE specifica-tions. All Double Block & Bleed valves are designed
Double Block and Bleed - AIChE
www.aiche.orgMar 25, 2012 · How does a double block and bleed work? A double block and bleed is often used for a more positive isolation of a process fluid from other equipment. It normally consists of two block valves (Valves 1 and 2 in the pictures) and a bleed valve (Valve 3) to a safe location, consistent with local environmental regulations.
API Specification 6D - American Petroleum Institute
www.api.orgAPI Specification 6D Specification for Pipeline and Piping Valves TWENTY-FOURTH EDITION | AUGUST 2014 | 108 PAGES | $150.00 | PRODUCT NO. G6D024
Block & Bleed Valves Monoflange - DK-LOK USA
www.dklokusa.comValves 1 Contents Primary Isolation Valve Applications Market Application Installation Advantages Technical Specification Ball Valve Specifications Outside Screw and Yoke(OS&Y) Needle Valve Specifications Globe Type Needle Valve Integral Block & Bleed Valve Ordering Information Product Range / Weights and Dimensions Monoflange Ordering ...
L&T Valves Process Ball Valves
www.lntvalves.com• Double Block and Bleed Plug Valves • Control Valves • Customised Solutions Designs for the valves are created by an experienced team of valve experts who have a deep understanding of user-industry processes. An extensive manufacturing and quality assurance infrastructure ensure that world-class
LT Valves Trunnion Mounted Ball Valve
www.lntvalves.comDouble Block and Bleed L&T Valves offers Trunnion-mounted Ball Valves (TMBV) that conform to API 6D. The valve, in closed position, blocks flow from both valve ends when the cavity between the seating surfaces is vented through a bleed connection provided on the body cavity. Inbuilt Double Block & Bleed feature enables on-line affirmation of seat
Medium- and High-Pressure Fittings, Tubing, Valves, and ...
www.swagelok.comDouble Block & Bleed Valves Medium Pressure Gaugeable Tube Fittings Needle Valves Up to 60 000 (4134) Relief Valves Tubing Up to 60 000 (4134) Applications Medium- and high-pressure fittings, valves, and components are designed to meet requirements of demanding applications such as the following: