Process Interface Valves - Swagelok
Class 300/Class 600 Nominal Flange Size Dimensions in . (mm) Mounting Holes 1/2 3 .75 (95 .2) 2 .62 (66 .5) 0 .62 (15 .7) 4 3/4 4 .62 (117) 3 .25 (82 .6) 0 .75 (19 .0) 4 4 .88 (124) 3 .50 (88 .9) 0 .75 (19 .0) 4 1 1/2 6 .12 (155) 4 .50 (114) 0 .88 (22 4) 4 2 6 .50 (165) 5 .00 (127) 0 .75 8 3 8 .25 (210) 6 .62 (168) 0 .88 (22 .4) 8 Class 900 ...
Download Process Interface Valves - Swagelok
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
BOLT & STUD DIMENSIONS FOR ANSI FLANGES
www.rhinofitt.co.uk150 200 250 300 350 375 400 425 450 475 500 525 540 FLANGE ABOVE DN 600 ARE NOT INCLUDED IN ANSI B16.5 AND THE CLASS DESIGNATIONS IN THESE LARGE DIAMETERS DO NOT IMPLY SPECIFIC TEMPERATURE/PRESSURE RATINGS Inch/Metric Bolting interchangeable for ANSI B16.5 flanges as below FOR USE 2-½" M56 M64 1-5/8" M42 1-3/4" M45 2-¼" M72 1-7/8" 2" 2-¼ ...
CLASS 150# FLANGE DIMENSIONS - FNW Valve
www.fnwvalve.comCLASS 150# FLANGE DIMENSIONS CLASS 300# FLANGE DIMENSIONS: ANSI B16.5 1/16” Raised Faced - Also Mate with ANSI B16.1 250# Flat Faced Flanges Size: Flange Diameter Flange Thickness: Bolt Circle Diameter: Bolt Hole DiameterNumber : of Bolt Holes
Class: 150 - 1500 Sizes: 1/2” - 12”
www.scvvalve.comClass: 3705 W.O.G. Design: B16.34 DUAL PLATE CHECKS WAFER & LUG Carbon & Stainless Wafer Sizes: 1.5” - 36” Wafer Class: 150 - 2500 Lug Sizes: 2” - 36” Lug Class: 150 - 900 Design: API 594 BOLTED COVER FULL PORT SWING CHECKS Carbon & Stainless Sizes: 2” - 36” Class: 150 - 2500 Design: API 6D THRU CONDUIT - SLAB & EXPANDING GATES ...
PVC & CPVC INJECTION MOLDED CLASS 150 FLANGES
www.spearsmfg.comMolded CLASS 150 Flange fittings are coupling devices designed for joining IPS (Iron Pipe Size) plastic piping systems, where frequent disassembly may be required, and can be used as a transitional fitting for joining plastic to metal piping systems. Suitability of application is at the discretion of the user. Pressure Rating 150 psi, water at ...
FLANGE DIMENSIONS - DIN - ShipServ
cdn1.shipserv.comFLANGE DIMENSIONS - DIN. D = Flange diameter n = Number of bolt holes. Hcd = Hole circle diameter d = Diameter of bolt holes. ... ANSI CLASS 150 ANSI CLASS 300 DN INCH D Hcd d BOLT n D Hcd d BOLT n inch inch 25 1” 108 80 16 1/2” 4 124 89 20 5/8” 4 32 1.1/4” 118 89 16 1/2” 4 133 98 20 5/8” 4 ...
API Standard 623
www.api.org⎯ flange d www.api.org Stan Globe V Bonne ION | SEPTEM ndard specifie of bolted bonn efinery and re rosion and ot eed for heavy rd sets forth t features: onnet, screw and yo rising stems, andwheels an tional, y-patte eck (nonretur y be positione, but is free t m under the d open positio rrow, conical seating surfa or butt-weldin dard alves ts ...
FLANGE DIMENSIONS TABLE TYPES - Australian Pipeline Valve
www.australianpipelinevalve.com.auto our Flange Chart – ‘Online Slide Rule’ above for flange dimensions. The number and diameter (mm) of the bolt holes for the example below of 300NB is: 12 x 25.4mm Class 150, 16 x 32mm Class 300, 16 x 34.9 Class 400, 20 x 34.9mm Class 600, 20 x 38.1mm Class 900, 16 x 54mm Class 1500 and 12 x 73mm Class 2500. 2
Variable Area MT3809G Series - Brooks Instrument
www.brooksinstrument.comflange choices along with several threaded options provide for flexible installations . ... VDI/VDE class 2.5, 1.6 VDI/VDE class 4, 2.5 VDI/VDE class 6 VDI/VDE class 2.5 ... Maximum Fluid Temperature 300°C/570°F 150°C/270°F Meter Dimensions
23 22 13 Steam and Steam Condensate Piping (072913)
www.uh.educ. Flanges: 150 lb. ANSI forged carbon steel, ASTM A181, Class 70, socket weld with Flexitallic Style CG Gasket, API 601 spiral wound 304SS with Grafoil Fill or accepted substitution. d. Cathodic Protection Gaskets: 1/8 inch thick Sealon by Ameriflex. Specify outside diameter (OD) and inside diameter (ID) of pipe and flanges.