(PROJECT STANDARDS AND SPECIFICATIONS)
Submersible Pumps (Wet Motor Type & Dry Motor Type) 6 Vertical Centrifugal Pumps 7 ... Electric motor load current (at discharge valve shutoff and open condition) x. Performance of all measuring instruments (pressure/ temperature gauges and flow meters) xi. ...
Download (PROJECT STANDARDS AND SPECIFICATIONS)
Information
Domain:
Source:
Link to this page:
Documents from same domain
PROJECT STANDARDS AND SPECIFICATIONS …
www.klmtechgroup.comKLM Technology Group Project Engineering Standard www.klmtechgroup.com Page : 2 of 13 Rev: 01 April 2012 KLM Technology Group #03-12 Block Aronia, Jalan Sri Perkasa 2
KLM Technology Group RECOMMENDED PRACTICE FOR ...
www.klmtechgroup.com(PROJECT STANDARDS AND SPECIFICATIONS) TABLE OF CONTENT SCOPE 2 ... The feasibility study for a chemical process design investigates both the technical and economic feasibility of the proposed project. The technical part of the ... Stanford Research Institution. UBC …
Guidelines for Ethylene Quench Towers - KLM Technology …
www.klmtechgroup.comGuidelines for Ethylene Quench Towers Karl Kolmetz GTC Technology LP Houston kkolmetz@yahoo.com Timothy M. Zygula omg21@cox.net Chee Mun Tham
PROCESS DESIGN OF GAS (VAPOR)-LIQUID SEPARATORS …
www.klmtechgroup.comFabric Filter - Commonly termed "bag filters" or "baghouses", are collectors in which dust is removed from the gas stream by passing the dust-laden gas through a fabric of some type. Flash Tank - A vessel used to separate the gas evolved from liquid flashed from a higher pressure to a lower pressure.
PROJECT STANDARDS AND SPECIFICATIONS general …
www.klmtechgroup.comCommissioning shall start from the point at which steps are taken to bring the ... Wherever a flange joint is broken after testing, e.g.,on heat exchangers, pipework, fired heaters and at machinery, then the joint rings or gaskets must be renewed.
(PROJECT STANDARDS AND SPECIFICATIONS)
www.klmtechgroup.comFlare load summary tables ... Design basis for winterizing and heat conservation shall be provided and a table indicating the basis of selection of tracer size and number for various pipeline ... Specifications, fire rating and identification of areas for fire proofing of …
PIPING MATERIAL SPECIFICATION (PROJECT STANDARDS …
www.klmtechgroup.comCarbon steel and alloy up to 9 Cr-Mo in dry service 1.6 mm Carbon steel and alloy up to 9 Cr-Mo in wet service 3.2 mm Galvanized steel 1.6 mm Stainless steel 0 mm Non-Metal such as GRP, HDPE, PVC, Non-metal lined, etc. 0 mm In special cases a greater corrosion allowance may be required. If a higher
PROJECT STANDARDS AND SPECIFICATIONS layout and sp
www.klmtechgroup.com2. Attention shall be given to the pertinent safety regulations, including health and welfare needs. 3. Hazardous and flammable materials require special handling, which can take up layout space. 4. If the process fluids are especially toxic, layout is affected by the need for close chemical sewers and other protection measures. Security ...
PROCESS DESIGN OF FURNACES (PROJECT STANDARDS AND ...
www.klmtechgroup.comfor the fouling of the heat exchanger train and the furnace inlet temperature shall be lowered in proportion to the design duty allowance. - If the case regarded as the highest duty is an extremely rare operation, the design duty may be 100% of the furnace duty in the highest duty case upon Company's approval. b. Reboilers and hot oil heaters:
PROJECT STANDARDS AND SPECIFICATIONS piping design
www.klmtechgroup.comProject Engineering Standard PLANT PIPING SYSTEMS DESIGN CRITERIA (PROJECT STANDARDS AND SPECIFICATIONS) Page 3 of 62 Rev: 01 June 2011 3. BP (British Petroleum) C P-3 "Plant Layout" C P-14 "Over Pressure Protection Systems" C P-16 "Passive Fire Protection of Structures & Equipment" Std.-107 "Forced Drought Burners for Fired Process Heaters" 4.
Related documents
SUBMERSIBLE MOTORS - Franklin Electric
franklinwater.comFranklin Electric submersible motors are a water-lubricated design. The fill solution consists of a mixture of deionized water and Propylene Glycol (a non-toxic antifreeze). The solution will prevent damage from freezing in temperatures to -40 °F (-40 °C); motors should be stored in areas that do not go below this temperature. The solution
Submersible Motors & Accessoreis Catalog - Franklin Electric
franklinwater.comSubmersible Motors & Accessoreis Catalog M1479 01.14 9255 Coverdale Road, Fort Wayne, Indiana 46809 Tel: 260.824.2900 • Fax: 260.824.2909 www.franklin-electric.com
TYPICAL SUBMERSIBLE PUMP INSTALLATION - Grover Electric
groverelectric.comG & G ELECTRIC AND PLUMBING DISTRIBUTORS, INC. INFORMATION SHEET COPYRIGHT 1989 37 These “How-To-Do-It” sheets have been reviewed in June 2007 by a professional Engineer. If you find a problem, please notify G & G Electric & Plumbing at 1900 78th Street, Ste. 101, Vancouver, Washington 98665 TYPICAL SUBMERSIBLE PUMP INSTALLATION 1.
Submersible electric Pumps Product Catalogue
www.ebara.comSubmersible electric pumps for waste water in AISI 304 Submersible electric pump for waste water in AISI 304 stainless steel. Pump body, impeller, motor cover, seal holder disc and motor case in AISI 304. Shaft in AISI 303 (part in contact with the liquid). Present the double mechanical seal with oil chamber: the upper one
SUBMERSIBLE PUMP SELECTION
www.nationalpumpcompany.comLightning and power surge damage are major causes of submersible motor failures, so a three-phase lightning arrestor is a must. The arrestor is mounted in the pump panel and grounded to both ground terminals onto pump panel and well head. If you use plastic pipe, the ground wire should also be connected to a stud on the motor to obtain