(PROJECT STANDARDS AND SPECIFICATIONS)
KLM Technology Group Project Engineering Standard www.klmtechgroup.com Page : 1 of 23 Rev: 01 Feb 2011 KLM Technology Group #03-12 Block Aronia, Jalan Sri Perkasa 2
Download (PROJECT STANDARDS AND SPECIFICATIONS)
Information
Domain:
Source:
Link to this page:
Documents from same domain
PROJECT STANDARDS AND SPECIFICATIONS …
www.klmtechgroup.comKLM Technology Group Project Engineering Standard www.klmtechgroup.com Page : 2 of 13 Rev: 01 April 2012 KLM Technology Group #03-12 Block Aronia, Jalan Sri Perkasa 2
KLM Technology Group RECOMMENDED PRACTICE FOR ...
www.klmtechgroup.com(PROJECT STANDARDS AND SPECIFICATIONS) TABLE OF CONTENT SCOPE 2 ... The feasibility study for a chemical process design investigates both the technical and economic feasibility of the proposed project. The technical part of the ... Stanford Research Institution. UBC …
Guidelines for Ethylene Quench Towers - KLM Technology …
www.klmtechgroup.comGuidelines for Ethylene Quench Towers Karl Kolmetz GTC Technology LP Houston kkolmetz@yahoo.com Timothy M. Zygula omg21@cox.net Chee Mun Tham
PROCESS DESIGN OF GAS (VAPOR)-LIQUID SEPARATORS …
www.klmtechgroup.comFabric Filter - Commonly termed "bag filters" or "baghouses", are collectors in which dust is removed from the gas stream by passing the dust-laden gas through a fabric of some type. Flash Tank - A vessel used to separate the gas evolved from liquid flashed from a higher pressure to a lower pressure.
PROJECT STANDARDS AND SPECIFICATIONS general …
www.klmtechgroup.comCommissioning shall start from the point at which steps are taken to bring the ... Wherever a flange joint is broken after testing, e.g.,on heat exchangers, pipework, fired heaters and at machinery, then the joint rings or gaskets must be renewed.
PIPING MATERIAL SPECIFICATION (PROJECT STANDARDS …
www.klmtechgroup.comCarbon steel and alloy up to 9 Cr-Mo in dry service 1.6 mm Carbon steel and alloy up to 9 Cr-Mo in wet service 3.2 mm Galvanized steel 1.6 mm Stainless steel 0 mm Non-Metal such as GRP, HDPE, PVC, Non-metal lined, etc. 0 mm In special cases a greater corrosion allowance may be required. If a higher
PROJECT STANDARDS AND SPECIFICATIONS layout and sp
www.klmtechgroup.com2. Attention shall be given to the pertinent safety regulations, including health and welfare needs. 3. Hazardous and flammable materials require special handling, which can take up layout space. 4. If the process fluids are especially toxic, layout is affected by the need for close chemical sewers and other protection measures. Security ...
PROCESS DESIGN OF FURNACES (PROJECT STANDARDS AND ...
www.klmtechgroup.comfor the fouling of the heat exchanger train and the furnace inlet temperature shall be lowered in proportion to the design duty allowance. - If the case regarded as the highest duty is an extremely rare operation, the design duty may be 100% of the furnace duty in the highest duty case upon Company's approval. b. Reboilers and hot oil heaters:
PROJECT STANDARDS AND SPECIFICATIONS piping design
www.klmtechgroup.comProject Engineering Standard PLANT PIPING SYSTEMS DESIGN CRITERIA (PROJECT STANDARDS AND SPECIFICATIONS) Page 3 of 62 Rev: 01 June 2011 3. BP (British Petroleum) C P-3 "Plant Layout" C P-14 "Over Pressure Protection Systems" C P-16 "Passive Fire Protection of Structures & Equipment" Std.-107 "Forced Drought Burners for Fired Process Heaters" 4.
PROCESS DESIGN OF AIR COOLED HEAT EXCHANGERS (AIR …
www.klmtechgroup.com15°C below the maximum product inlet temperature. * Unless otherwise agreed by the Company, the product outlet temperature shall not be less than 10°C above the design air temperature. 4. The advantages of forced and induced draft types are listed in Appendix D. These should be weighed carefully before deciding on the choice of unit. 5 ...
Related documents
VENT SILENCERS - blowers - rotary positive
www.eiwilliams.comE.I. Williams STEEL DIVISION BUILDING SOUND SOLUTIONS OTHER PRODUCTS AVAILABLE: • ROTARY POSITIVE BLOWER INTAKE AND DISCHARGE SILENCERS reference catalogue 1 • BASE SILENCERS FOR ROTARY POSITIVE BLOWERS reference catalogue 2
Introduction to Pneumatic Conveying of Solids
www.aiche.orgRotary Lobe Blowers –often called “Roots” blowers Fans Compressors. Typical air mover performance curves pressure ume Fan Compressor Blower. Lobe Blower Performance Curves Pressure Vacuum. Rotary Lobe Blower These are true positive displacement devices. Some suppliers will provide a tri-lobe model in order to cut down on the