Pspice Tutorial
Variable Resistor R_var Analog ... To simulate a short circuit place a small resistor across node A and node B. For this example I used a 1 femto ohm. You should get Isc = 1.765mA for a short circuit current. For Voc replace the value with a large value, for this example I use
Download Pspice Tutorial
Information
Domain:
Source:
Link to this page:
Documents from same domain
MATLAB Commands and Functions
www.hkn.umn.eduString Functions findstr Finds occurrences of a string. strcmp Compares strings. char Creates character string array. MATLAB Commands – 14 Numerical Methods Polynomial and Regression Functions conv Computes product of two polynomials deconv Computes ratio of polynomials.
Related documents
Chapter 14 BJT Models - University of Washington
class.ece.uw.eduFor both the vertical and lateral the resistor model parameters, RB, RBM, RE, and RC are scaled by the following equation. where R is either RB, RBM, RE, or RC. BJT Current Convention The direction of current flow through the BJT is assumed for example purposes in Figure 13-1. Use either I(Q1) or I1(Q1) syntax to print the collector current.
How to Simulate a Variable Resistor in LTSpice
eecs.oregonstate.eduof resistor that you want to be variable, to be {R} • Click on .op (far right on the toolbar) • Type: .step param R 1 10k 1k (steps from 1 to 10K in 1k increments) o. You will need to fill in the correct values, based on the resistive sensor you used • Click Simulate -> Run -> Go to the DCop pnt tab …
Laboratory 2: Voltage and current dividers, Wheatstone ...
faculty.ontariotechu.ca2. Using the same circuit in Figure 2-1, add a load resistor RL in parallel to R2 and use the values V1 of 10 V, R1 and R2 both of 2 k Ω and RL of 1 kΩ, 2 kΩ, 3.3 kΩ, 4.7 kΩ, 5.6 kΩ, and 10 kΩ: 2.1. Simulate this loaded voltage divider circuit in OrCad/PSpice and measure the output voltage for each value of RL.
HSPICE User Guide: Simulation and Analysis
inst.eecs.berkeley.eduHSPICE® User Guide: Simulation and Analysis Version B-2008.09, September 2008
DC motor circuits
static.sparkfun.comArduino cannot supply variable DC output! Arduino lacks a true analog output! Use Pulse-width modulation (PWM) to simulate a variable DC supply voltage! PWM is a common technique for supplying variable power levels to “slow” electrical devices such as …
pspice tutorial transient
www.csun.eduFor this part we will simulate the circuit as shown in figure 1. Open a new PSPICE project ... This time a display window will open and a graph of the resistor voltage will appear. Of course, since this is a DC circuit, all we see is a straight line, or constant voltage. ... plotting a graph with time as the x-axis variable. Later in the course ...
NI myRIO Project Essentials Guide
www.ni.comcurrent-limiting resistor; you may instead use two series-connected 100 resistors or two parallel-connected 470 ... Blink two adjacent LEDs to simulate a railroad crossingsignal. 3. Blink the green and blue LEDs of the RGB ... DISCRETELED 4. Create an LED variable-intensity dimmer with the PWM Express VI to create a pulse-width ...
Application of LTSpice Modeling to Vishay Temperature Sensors
www.vishay.comThe first run will simulate the nominal case; the remaining runs will simulate a Gaussian normal distribution around the nomina l with a standard deviation of a fourth of the tolerance. We have applied this modification to the TFPT (cf point 5.1). In the netlist of the TFPT model, the function MC(x, tolx) must be replaced by MCG(x,tolx).