Pump and Motor Preventative Maintenance Program
Jun 08, 2011 · pump alignment Align the pump/motor coupling to allow for efficient torque transfer to the pump. X Check mountings Check and secure all pump mountings. X Check bearings Inspect bearings and drive belts for wear. Adjust, repair, or replace as necessary. X Motor condition Check the condition of the motor through temperature or vibration analysis ...
Download Pump and Motor Preventative Maintenance Program
Information
Domain:
Source:
Link to this page:
Documents from same domain
Friction Losses in Pipe Fittings Resistance …
www.metropumps.comFriction Losses in Pipe Fittings Resistance Coefficient K (use in formula hf = Kv²/2g) Fitting LD Nominal Pipe Size ½ ¾ 1 1¼ 1½ 2 2½-3 4 6 8-10 12-16 18-24
www.metropumps.com
www.metropumps.comcan lead to extending the life of rotary equipment by improving seal design and material selection, installation and operating procedures, and environ- mental controls. 8.2 Causes of Mechanical Seal Failure The failure of a seal may be the result of:
Related documents
Pumps & Sprayers Warranty Return Submission Form
images.harborfreight.com46750 pump dirty water s.s.submer3/4 62643 2.3 gallon manual fluid extrac 68387 1hp st stl shallow well pump 47334 self-priming jiggler pump 62783 drill water pump - 210 gph 68388 3/4hp cast iron shllw wll pump 47906 pump shallow well s.s. 1 hp 62961 multi-use transfer pump 68390 3/4hp automatic booster pump
GL-03: FIRE SAFETY EQUIPMENT SIGNAGE - Department of …
www.dfes.wa.gov.aubooster connection relay pump – level _ _ (to boost to level _ _) (boost pressure _ _ kpa) sprinkler stop valve inside sprinkler stop valve inside 1. call fire brigade (000) _ _ _ _ _ 2. make sure fire is out. 3. close main stop valve (shutting off water supply). 4. open waste valve (draining installation) 5. call maintenance contractor ...
Centrifugal Pump Selection Guide - Goulds Pumps
www.gouldspumps.compump design and the adoption of smart technologies. Rheinhütte Pumpen ... water supply, booster, low lift, and high lift. For non-clog solids handling, a range of horizontal, vertical sump, and submersible pumps have helped professional …
Pump Station Design Guidelines Second Edition
www.jensenprecast.combooster pump systems, the discharge could be in a pressurized holding tank. So tank pressure must be taken into consideration during design. In a typical JES lift station, the force main discharges to gravity in either a manhole or other holding structure. Figure 3
OPERATING AND MAINTENANCE MANUAL - …
www.montgomerycountymd.govJul 17, 2003 · A Hale Pump is a quality product: ruggedly designed, accurately machined, carefully assembled and thoroughly tested. In order to …
Pump Product Catalog
www.pp-s.comspecialty designs. Each pump is identified by its formal designation and accompanied by a full-color cutaway illustration. Applicable engineering standards are listed along with performance characteristics and key features. The symbols shown at right are used to identify each pump’s primary market applications.
Fire Pump Inspection Checklist - PPSA
www.ppsa.orgA booster pump reinforces the public water supply when the public water main cannot provide the volume or pressure needed to supply an automatic sprinkler system. A fire pump and tank with a self-contained water supply can be used either to supplement public water or as a source of water where no public supply is available. A Pump Must Not Fail
14. Design of plumbing systems for multi-storey buildings
www.who.intWhere booster pump sets are permitted to draw directly from public water mains, the public drinking-water supply must be adequate to meet the peak demands of all buildings in the area. Otherwise, there is a high risk of backflow and subsequent contamination of the mains from buildings not equipped with a booster pump. Building booster