Rigid Sheet Specifications
B. Stainless steel top caps shall be made of #400 series stainless steel. C. Stainless steel vertical divider bars shall be #400 series stainless steel on galvanized steel. D. Aluminum top caps, inside corners, divider bars shall be extruded from 6063-T5 aluminum. 2.05 FINISHES A. Color or pattern of Palladium® Rigid Vinyl Sheet to
Download Rigid Sheet Specifications
Information
Domain:
Source:
Link to this page:
Documents from same domain
Tape-On
www.inprocorp.com7. Color Consistency: Provide components matched in accordance with SAE J-1545 - (Delta E) with a color difference no greater than 1.0 units using CIE Lab, CIE CMC, CIE LCh, Hunter Lab or similar color space scale systems. 1.05 SUBMITTALS A. Product Data: Manufacturer's printed product data for each type of corner guard specified.
Important
www.inprocorp.comcolor match caulk (optional) inpro #333 extension roller palladium® rigid sheet inpro bond, xt-2000+, or 3m fastbond 30 inpro #545 trowel 407 top cap 407a optional aluminum top cap 409 inside corner 409a optional aluminum inside corner 408 vertical divider 408a optional aluminum vertical divider tape-on corner guard 420a optional aluminum ...
Related documents
RECTANGULAR DUCTS - AIC STEEL
www.aicsteel.comHR01 is supplied with various materials Galvanized steel G90 and G115 in accordance with ASTM A653, Black Steel in accordance with ASTM A366 supplied with primer paint, Stainless steel 304 and 316 in accordance with ASTM A240 and Aluminum Alloy 3003-H14 in accordance with ASTM B209.
ZINC COATINGS - American Galvanizers Association
galvanizeit.orgContinuous sheet galvanizing is also a hot-dip process, but is only applied to steel sheet, strip, and wire. A coil to coil process, steel sheet from 0.010 to 1.70 inches (0.25 mm to 4.30 mm) thick and up to 72 inches (1,830 mm) wide is passed as a continuous ribbon through cleaning baths and molten zinc at speeds up to 600 feet per minute.
SHEET METAL DESIGN GUIDE. - GoProto, Inc.
goproto.comALUMINUM Galvanized steel is steel coated with zinc during a zinc solution heat batch. This process protects the steel from corrosion and cracks and, like aluminum, has a good strength-to-weight ratio. Galvanized steel has a lower cost per pound than aluminum but may have some issues in adhesion of paints depending on end use.
SPIRAL DUCT & FITTINGS - Eastern Sheet Metal
www.easternsheetmetal.comGauge selection for galvanized steel (ASTM A 653), paint grip steel, type 304 and 316 stainless steel, and Eastern Poly Coated Steel (PCS).* Fittings are …
Stick Consumable Charts - Global Industrial
www.globalindustrial.comStainless Steel Stainless steel contains a high chromium and low carbon content, and upon contact with oxygen creates a chromium oxide layer that gives passive protection against corrosion from moisture. When certain high-strength alloys such as aluminum come into contact with carbon steel, such as being brushed by carbon steel wire, a
Technical Data Sheet - Jotun
www.jotun.comfor properly prepared carbon steel, galvanized steel, shop primed steel, stainless steel, aluminum and concrete substrates. Suitable as maintenance coating on a wide range of aged coating surfaces. It can be applied at sub zero surface temperatures. Approvals and certificates Approved for PSPC for Water Ballast Tanks according to IMO Res. MSC ...
Gauge and Weight Chart for - Pittsburgh Air Systems
www.pittsburghairsystems.comGauge and Weight Chart for Sheet Steel, Galvanized Steel,Stainless Steel, and Al September 1st, 2004 This article provides a quick reference to gauges of material, pounds per square foot, and gauge decimal equivalents. Gauge Sheet Steel Galvanized Steel Stainless Steel Aluminum Gauge Decimal Lbs. per Sq. Ft. Gauge Decimal Lbs. per Sq. Ft. Gauge ...