Safe Operating Procedure
Safe Operating Procedure (Created 9/10) 1 ... standards specify minimum safe distances that are to be maintained while working in an aerial lift, as indicated in the table below. If these distances cannot be achieved, do ... o Never exceed the manufacturer’s specified maximum load (which includes the weight of the person and all tools ...
Download Safe Operating Procedure
Information
Domain:
Source:
Link to this page:
Documents from same domain
(Revised 9/16) FIRST AID KITS - University of …
ehs.unl.edu(Revised 9/16) FIRST AID KITS _____ While UNL facilities are not required by law to be equipped with ...
Safe Operating Procedure - University of …
ehs.unl.eduSafe Operating Procedure ... First aid kits are encouraged in all work ... injury/illness should seek medical treatment at the University Health Center or their ...
GASES UNDER PRESSURE HAZARDS & RISK MINIMIZATION
ehs.unl.eduGases in high-pressure cylinders contain an extraordinary amount of stored energy. If a cylinder valve is breached (i.e., breaks off when the cylinder falls and strikes a hard surface, etc.), the
FORKLIFT/POWERED INDUSTRIAL TRUCK SAFETY
ehs.unl.edu• PITs should be driven on the right side of the road or aisle-way, and operated at a safe speed with due regard for traffic and conditions (slippery surfaces,
PERSONAL PROTECTIVE EQUIPMENT (PPE) – BODY …
ehs.unl.edu(Created 7/12; Revised 11/15) UNL Environmental Health and Safety · (402) 472-4925 · http://ehs.unl.edu. unnecessarily burdened • Protective clothing should be ...
Chemical Safety
ehs.unl.eduExposure Limits Permissible Exposure Limits - (PEL's) Recommended Exposure Limits – (REL’s) ... flashpoint > 73 F, < 100 F, no bp limits Amyl Acetate, Xylene. 35 Chemical Safety 3 Combustible Liquids Solvents! ... Acetonitrile, Adriamycin, Heavy Metals, Cannabis, Dimethyl sulfoxide, Ethylene oxide, Formaldehyde, Ketamine, d-Limonene ...
Compressed Gas Safety.ppt
ehs.unl.edu−20 feet from oxygen & combustible material. −Never place anything on top of cylinder. Oxygen −20 feet from flammable or combustible material. Separation can be 1 hour fire wall. Cylinders in use or connected can be stored together.
1. Why Report Near Misses?
ehs.unl.eduJun 20, 2014 · Identifying and investigating near-misses is a key element to finding and controlling risks before workers are injured. The information gathered through near-miss reporting is evaluated to determine root causes and hazard mitigation strategies. “Lessons learned” are shared in a general way (you are not identified) so all
(Revised 8/15) GENERAL MACHINE SAFETY
ehs.unl.eduGENERAL MACHINE SAFETY _____ This SOP is intended to provide general safety guidance for power-driven (including ... Hazard Overview . Potential hazards of operating machines and equipment are numerous. Some of the ... preventative maintenance. Do not use compressed air for cleaning of debris.
BASIC ELECTRICITY 101 - Environmental Health & Safety
ehs.unl.eduBASIC ELECTRICITY 101 Kevin Booker, Executive Director State Electrical Division of Nebraska. OBJECTIVES Review some typical hazards associated with electricity and learn how to mitigate the hazards. In the United States, electrical hazards are ... Product Safety Commission) went to the electrical manufacturers of GFCI’s and
Related documents
WORKING AT HEIGHTS SAFE WORK METHOD …
sayfa.com.auWORKING AT HEIGHTS SAFE WORK METHOD STATEMENT (SWMS) THE IMPORTANCE OF COMPLETING A SAFE WORK METHOD STATEMENT (SWMS) ... system is the responsibility of the installer and should be verified by a structural engineer or a site specific live load test done to ensure conformance.
OPERATING RULES FOR INDUSTRIAL TRUCKS
www.dir.ca.gov(27) A loaded vehicle shall not be move d until the load is safe and secure. General Industry Safety Order 3650 Industrial Trucks. General (Part (t)) (28) Extreme care shall be taken when tilting loads. Tilting forward with the load engaging means elevated shall be prohibited except when picking up a load.
SOP 10 Safe lifting operations
www.eeslindia.orgmore than 12 months previously) and specifying the Safe Working Load, prior to first use. A thorough examination is to be performed following the repair or replacement of a structural component. All other lifting Equipment must undergo a thorough examination at …
Safe use of all-terrain vehicles (ATVs) in agriculture and ...
www.hse.gov.ukSafe use of all-terrain vehicles (ATVs) in agriculture and forestry ... It covers the two main types used in off-road working in agriculture, forestry and the land-based industries, namely: ... capable of towing a load such as a trailer, a trailed appliance or other equipment.
Safe working with bales in agriculture INDG125 - HSE
www.hse.gov.ukHealth and Safety Executive Safe working with bales in agriculture Page 6 of 10 Moving bales Vehicles and equipment Use properly designed, constructed and maintained bale handling equipment and trailers or vehicles that allow loads to be secured to them.
Protect Workers Operating and Working Near Forklifts
www.osha.gov• Never exceed the rated load, and ensure loads are balanced. • Make sure you have enough clearance when raising and loading materials. • Watch for pedestrians and observe speed limits. • Keep a safe distance from platform and ramp edges. For more information on ways to keep workers safe while working with or around forklifts, visit
SAFE USE OF LIFTING EQUIPMENT - Safe Quarry
www.safequarry.com• The load must be within the capability of the lifting equipment – you will need to calculate the safe working load for the lifting equipment and know how to determine the weight of the load. • Overload indicators and any other warning devices that form part of the lifting equipment are working correctly and have been tested.
High risk construction work Safe Work method statement ...
www.safework.nsw.gov.auensure load has not shifted during transport. • Loads to be placed on pallets, stillage or pre-slung prior to arriving on site. • Platform/ladder to be available to release straps caught on load. • False work and formwork will be installed by competent workers in accordance with manufactures design or engineered recommendations.