Solutions Features & Benefits - MKS Instruments
WWW. MKSI n ST. COM SRG-3 SPINNING ROTOR GAUGE SYSTEM The Spinning Rotor Gauge (SRG) line is well established with users around the world as a stable, high accuracy transfer standard for high vacuum pressure measurements.
Download Solutions Features & Benefits - MKS Instruments
Information
Domain:
Source:
Link to this page:
Documents from same domain
250E Gas Inlet Pressure/Flow Control Module
www.mksinst.comWWW. MKSINST. COM 250E PRESSuRE/FLOW COnTROL MODuLE The 250E is a self-contained PID control module designed to provide optimized control of the total pressure or flow of a gas (or gases) in a dynamic closed-loop system.
649A Compact Pressure Controller - MKS Instruments
www.mksinst.comWWW. MKSINST. COM Type 649A ElECTRONiC PRESSuRE CONTROllER WiTh MASS-FlO® METER The MKS Type 649 is a single instrument that provides both pressure control and flow
Pressure & High Accuracy Systems - Process …
www.mksinst.comWWW. MKSINST. COM High Accuracy Systems 690A And 698A SEnSOrS 670B SignAl COndiTiOnEr The High Accuracy Baratron® Pressure Measurement Systems combine advanced capacitance diaphragm sensor technology and …
Hydrogen Purity Analysis by FTIR - MKS Instruments
www.mksinst.comAliation Note Hydrogen Purity Analysis by FTIR. PROBLEM. Historically, hydrogen has been employed in a variety . of industrial chemical processes. Typically, the purity
GE50A Elastomer-sealed, Digital Mass Flow Controller
www.mksinst.comWWW. MKSINST. COM GE50A ElASTOMER SEAlED, DiGiTAl MASS FlOw COnTROllER The GE50A is a general purpose, elastomer sealed MFC well suited for a wide variety of
Related documents
Series 719 - Watts Water Technologies
media.wattswater.comSeries 719 Double Check Valve Assemblies Sizes: 1⁄2" – 2" (15 – 50mm) Series 719 Double Check Valve Assemblies are designed to protect drinking water supplies from dangerous cross-connec-
DEMO ONLY TThrough-Holehrough-Hole SSolder Joint …
training.ipc.org7 Through-Hole Solder Joint Evaluation Training and Reference Guide Through-Hole Solder Joint Evaluation Training and Reference Guide 8 Defect Class 1, 2, 3 References: A-610D: 7.5.5.3, Table 7-6 J-STD-001D: 6.3.2, Table 6-5 0% of the component side land area is covered with wetted solder.
DIFFERENTIAL PRESSURE - Dwyer Instruments, Inc.
www.dwyer-inst.comBulletin TE-475 SPECIFICATIONS Service: Air and compatible gases. Wetted Materials: Consult factory. Accuracy: ±0.5% FS, 60 to 78°F (15.6 to 25.6°C); 1.5% FS from 32 to 60°F and 78 to 104°F (0 to 15.6°C and 25.6 to 40°C). Pressure Hysteresis: ±0.1% of FS. Pressure Limits: See chart. Temperature Limits: 0 to 140°F (-17.8 to 60°C). Compensated Temperature Limits: 32 to 104°F (0 to 40°C).
SCREW DESIGN BASICS - TAPPI
www.tappi.orgSCREW DESIGN BASICS The Processor Point Of View Andrew W. Christie Optex Process Solutions, LLC www.optexprocesssolutions.com
Waters e2695 separations Modules
www.waters.comWaters e2695 separations Modules Waters® e2695 family of Separations Modules, with its integrated solvent and sample management capabilities, provide the flexibility and ruggedness needed to accommodate an enormous range of HPLC separation challenges. SOLVENT MANAGEMENT Number of solvents One to four
ACQUITY UPLC H-Class System - Waters
www.waters.comACQUITY UPLC H-Class System Instrument Specifications 3 Maximum sample capacity 768 in two 384-well plates or, 96 in 2-mL vial holders Four additional positions for dilution functions
Pressure Gauge for General Purpose G15/G27 Series RoHS
content2.smcetech.comRoHS 1 R 8 1 R 8 Model Pressure range (1) MPa MPa MPa Indication unit Connection thread Note G36-2-01 G36-4-01 G36-7-01 G36-10-01 GA36-10-01 0 to 0.2 0 to 0.4 0 to 0.7
Pipe Flow Calculations - web2.clarkson.edu
web2.clarkson.edu1 Pipe Flow Calculations . R. Shankar Subramanian . Department of Chemical and Biomolecular Engineering . Clarkson University . We begin with some results that we shall use when making friction loss calculations for steady,