Technical data sheet PLA - Farnell element14
Feb 28, 2017 · Tensile modulus Tensile stress at yield Tensile stress at break Elongation at yield Elongation at break Flexural strength Flexural modulus Izod impact strength, notched (at 23˚C) Charpy impact strength (at 23˚C) Hardness Melt mass-flow rate (MFR) Heat deflection (HDT) at 0.455 MPa Heat deflection (HDT) at 1.82 MPa Glass transition
Download Technical data sheet PLA - Farnell element14
Information
Domain:
Source:
Link to this page:
Documents from same domain
Stainless Steel Grade 316 / 1 - Farnell element14
www.farnell.comabc® Aalco is a registered trademark of Aalco Metals Ltd © Copyright: Aalco Metals Ltd, The Hersham Centre, Hersham Green, Hersham, Surrey KT12 4HP All Data is indicative only and must not be seen as a substitute for the full specification from which it is drawn.
SAFETY DATA SHEET COPPER GREASE - Farnell …
www.farnell.comReport Date : 10/10/2013 1 / 7 Revision Date 10/10/2013 Revision 6 Supersedes date 01/08/2011 V5 SDS No. 16238 SAFETY DATA SHEET COPPER GREASE
PRECISION TOOLS - Farnell element14
www.farnell.com10 20 30 40 50 60 70 80 90 100 110 PRECISION TOOLS CATALOGUE www.starrett.com.sg • +65 6365 1088
C60N/H miniature circuit breakers Multi 9 Merlin …
www.farnell.comC60N/H miniature circuit breakers Multi 9 Merlin Gerin The C60N circuit-breaker is a miniature circuit-breaker used for the protection of …
www.weidmueller.com Data sheet
www.farnell.comData sheet Creation date November 22, 2016 12:42:25 PM CET Catalogue status 18.11.2016 / We reserve the right to make technical changes. 1
DOW€CORNING® 732 Multi-Purpose Sealant
www.farnell.comDOW€CORNING® 732 Multi-Purpose Sealant € Product Information TYPICAL PROPERTIES Specifications writers: These values are not intended for use in …
XLP 8-Bit Development Board User's Guide
www.farnell.comXLP 8-BIT DEVELOPMENT BOARD USER’S GUIDE 2011 Microchip Technology Inc. DS41581A-page 3 Table of Contents Chapter 1. Introduction to the XLP 8-Bit Board
Material - Safety - Data Sheet (MSDS) - Farnell …
www.farnell.comNo.5 2/6 3. Composition and Informations on Ingredients Each cell consists of a hermetically sealed metallic container containing a number of chemicals and
Diodes - Farnell element14
www.farnell.comDiodes BA Series Page <2> 20/06/12 V1.1 www.element14.com www.farnell.com www.newark.com Maximum Ratings TA = 25°C unless otherwise specified Type Number Symbol BAW56 / BAV70 / BAV99 Units
Mitutoyo General Catalog - Farnell element14
www.farnell.comMiscellaneous List of products Move to other products SPC Caliper Depth gage H eight gage Micrometer Inside micrometer Micrometer head Indicator Test indicator
Related documents
Atlas 1045 Medium Tensile Carbon Steel Bar 1045
www.atlassteels.com.auTensile Strength (MPa) 0.2% Proof Stress (MPa) Elongation (% ) Reduction of Area (% ) Impact Charpy (J) up to 40 incl 650 – 800 430 min 16 min 40 min 25 min >40 to 100 incl 630 – 780 370 min 17 min 45 min 25 min >100 to 250 incl 590 - 740 340 min 18 min - 22 min >250 to 500 incl 590 - 740 320 min 17 min - 20 min ...
Mylar - DuPont Teijin Films
usa.dupontteijinfilms.comTensile Strength, psi Figure 11. Tensile Strength of Mylar after Heating in 150°C (302°F) Air Figure 12. Tensile Elongation of Mylar after Heating in 150°C (302°F) Air 0 0 50 100 150 200 1,000 2,000 3,000 4,000 5,000 Time, hr at 150°C (302°F) Tensile Elongation, % Figure 10. Effect of Temperature on the Removal of Water from Mylar 0 (32 ...
Thermoplastic Ployurethane Elastomers (TPU) BASF
plastics-rubber.basf.comMaximum force elongation ε max is the elongation corresponding to the tensile strength. Elongation at break εB is the elongation corresponding to the tear strength In the case of unreinforced Elastollan® grades at room temperature, differences are not generally observed, e.g., tear strength and tensile strength correspond (Fig. 15). A
A Beginner’s Guide - PerkinElmer
resources.perkinelmer.com3 Q What is DMA? A Dynamic Mechanical Analysis, otherwise known as DMA, is a technique where a small deformation is applied to a sample in a cyclic manner. This allows the materials response to stress, temperature, frequency and other values to be
Experiment One (1) Tensile Stress Testing
web.eng.fiu.eduExperiment One –Tensile Stress Test The tensile testing machine consists of an electro-mechanical test system that applies uniaxial loading in a uniform manner to test specimens. It is general purpose in its capabilities and applications. The system performs load versus elongation (stress versus strain) tests which
Tensile Testing Basics Quality Magazine - ADMET
www.admet.comlength. The ultimate tensile strength, or peak stress, is represented by point D. Total elongation, which includes both elastic and plastic deformation, is the amount of uniaxial strain at fracture and is depicted as strain at point Z. Percent elongation at break is determined by removing the fractured specimen from the grips; fitting
Thermoplastic Polyurethane Elastomers (TPU) - BASF
www.basf.comTensile strength MPa DIN 53504-S2 30 40 45 40 45 50 45 30 Elongation at break % DIN 53504-S2 850 700 650 700 600 480 600 650 Stress at 20 % elongation MPa DIN 53504-S2 1.5 2 2 2.5 2.5 3.5 4 Stress at 100 % elongation MPa DIN 53504-S2 3.5 4 4.5 6 6 7 7 Stress at 300 % elongation MPa DIN 53504-S2 6.3 8 8 8 10 12 13
Tensile properties of paper and paperboard (using constant ...
www.tappi.orgJun 13, 2006 · T 494 om-01 Tensile properties of paper and paperboard / 2 (using constant rate of elongation apparatus) 2. Definitions 2.1 Tensile strength, the maximum tensile force developed in a test specimen before rupture on a tensile test …