Technical DaTa SheeT Polycarbonate
Polycarbonate is a tough, dimensionally stable, transparent thermoplastic that has many applications which demand high performance properties. This versatile thermoplastic maintains its properties over a wide range of temperatures, from -40”F ... Window Grade is optically clear, providing total luminous transmittance and a very low haze ...
Download Technical DaTa SheeT Polycarbonate
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical DaTa SheeT Polypropylene - Laminated Plastics
laminatedplastics.comTYPICAL PROPERTIES of POLYPROPYLENE ASTM or UL test Property Homopolymer Co-Polymer Flame Retardant PHYSICAL D792 Density (lb/in³) (g/cm³) 0.033 0.905 0.033 0.897 0.035 0.988 D570 Water Absorption, 24 hrs (%) <0.01 0.01 0.02 MECHANICAL D638 Tensile Strength (psi) 4,800 4,800 4,300 D638 Tensile Modulus (psi) 195,000 - -
Technical DaTa SheeT Polyethylene - Laminated Plastics
laminatedplastics.comPOlYeThYlene GRaDeS high Density Polyethylene (hDPe) Representing the largest portion of the polyethylene applications, HDPE offers excellent impact resistance, light weight, low moisture absorption, and high tensile strength. HDPE is also non-toxic and non-staining and meets FDA and USDA certifica-tion for food processing. Benefits Abrasion ...
Technical DaTa SheeT high Density Polyethylene
laminatedplastics.comhigh Density Polyethylene (HDPE) Representing the largest portion of the polyethylene applications, HDPE offers excellent impact resistance, light weight, low moisture absorption, and high tensile strength. HDPE is also non-toxic and non-staining and meets FDA and USDA certifica-tion for food processing. Benefits Abrasion Resistant
Technical DaTa SheeT Teflon (PTFe) - Laminated Plastics
laminatedplastics.com(260 C). It is the most chemically resistant plastic available and only a few chemicals react with it. PTFE mechanical properties are low compared to other engineering plastics, but its integrity is maintained over a wide temperature range - from -400 to 500°F (-240 to 260°C).
Technical DaTa SheeT lexan (Pc) Polycarbonate
laminatedplastics.comnTe Te inoration containe erein are typical ales intene or reerence an coparison prposes only Tey sol nT be se as a basis or esin specifications or ality control contact s or anactrers’ coplete aterial property ataseets.
Technical DaTa SheeT Plexiglass (PMMa)
laminatedplastics.comTYPICAL PROPERTIES of ACRYLIC PMMA ASTM or UL test Property Acrylic PHYSICAL D792 Density (lb/in³) (g/cm³) 0.043 1.18 D570 Water Absorption, 24 hrs (%) 0.3 MECHANICAL D638 Tensile Strength (psi) 8,000 - 11,000 D638 Tensile Modulus (psi) 350,000 - 500,000 D638 Tensile Elongation at Break (%) 2 D790 Flexural Strength (psi) 12,000 - 17,000
Technical DaTa SheeT nylon - Laminated Plastics
laminatedplastics.comse as a asis o esin specifications o ality contol contact s o anactes’ coplete ateial popety ataseets. all ales at F c nless oteise note. Technical DaTa SheeT nylon (Polyamide) The exceptional bearing and wear properties of Nylon make it one of the …
TECHNICAL DATA SHEET Mylar® - Laminated Plastics
laminatedplastics.comMylar® (Polyester Film) Mylar® exhibits superior strength, heat resistance, and excellent insulating properties. The unique qualities of Mylar® are found in many consumer, high tech, and electronic markets. Mylar® Polyester Film is ideally suited for a wide range of uses such as
Technical DaTa SheeT acetal (POM) - Laminated Plastics
laminatedplastics.comCopolymer Acetal has superior performance in continuous high heat and hot water environments. Copolymer Acetal also tends to have less porosity than Homopolymer Acetal. Grades of Acetal aceTal cOPOlYMeR (unfilled) The copolymer grade offers excellent performance at a slightly lower cost than Delrin®. Certain grades are FDA, USDA, NSF,
Technical DaTa SheeT PVc - Laminated Plastics
laminatedplastics.comDielectric Strength (V/mil) short time, 1/8" thick 544 1250 D150 Dielectric Constant at 60 Hz 3.2 3.7 D150 Dissipation Factor at 60 Hz .0096 - D257 15Volume Resistivity (ohm-cm)at 50% RH 5.4 x 10 3.4 x 1015 S available
Related documents
Makrolon® 2407 PC Bayer MaterialScience - 2006-07-18
www.b2bpolymers.comLuminous transmittance 89 % ISO 13468-1, -2 Rheological calculation properties ... Transparent, High impact or impact modified, Light stabilized or stable to light, U.V. stabilized or stable to weather Other Text Information Injection Molding PREPROCESSING Max. Water content: 0,02 %
% b.o. ISO 2577 0.5 - 0.7 C Molding shrinkage, normal ...
solutions.covestro.comLuminous transmittance (clear transparent materials) 3 mm % ISO 13468-2 88 Luminous transmittance (clear transparent materials) 4 mm % ISO 13468-2 87 Processing conditions for test specimens C Injection molding - Melt temperature °C ISO 294 280
Makrolon® 2458 - Covestro
solutions.covestro.comLuminous transmittance (clear transparent materials) 3 mm % ISO 13468-2 88 Luminous transmittance (clear transparent materials) 4 mm % ISO 13468-2 87 Processing conditions for test specimens C Injection molding - Melt temperature °C ISO 294 280
Test Methods for Color Measurement
ucanr.eduASTM D1003, “Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics,” provides a procedure for the instrumental measurement of luminous transmittance and haze of materials with haze values up to 30%. ASTM D1209, “Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale),”
Denka Performance Plastics
www.denka.co.jpABS Resin /Transparent Resin /CLEAREN Denka Performance Plastics. 1 2 220℃、98N 200℃、49N ... Total Luminous Transmittance Haze Applications. 5 6