Tnemec
We would like to show you a description here but the site won’t allow us.
Download Tnemec
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET: POWER-TREAD - SERIES 237
production.tnemec.comwith ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed three pounds per 1,000 square feet in a 24 hour period), F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes ...
PRODUCT DATA SHEET: EVERTHANE - SERIES 248
production.tnemec.comwith ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed three pounds per 1,000 square feet in a 24 hour period), F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes ...
PRODUCT DATA SHEET: HYDRO-ZINC - SERIES 94-H 2 O
production.tnemec.comequipped with an agitator and keep pressure pot at same level or higher than the spray gun. Compressed air must be dry. Airless Spray Tip Orifice Atomizing Pressure Mat’l Hose ID Manifold Filter 0.015”-0.019” (380-481 microns) Reversible Tip 3000-4000 psi (207-276 bar) 1/4” or 3/8” (6.4 or 9.5 mm) 60 mesh (250 microns)
PRODUCT DATA SHEET: HI-BUILD EPOXOLINE - SERIES 66
production.tnemec.comPRODUCT DATA SHEET SERIES 66 PRODUCT PROFILE GENERIC DESCRIPTION Polyamide Epoxy COMMON USAGE Industry standard for epoxy coatings for over 40 years. Known for its forgiving application characteristics in adverse and varied conditions, and for benchmark performance. COLORS Refer to Tnemec Color Guide.
PRODUCT DATA SHEET: TNEME-ZINC - SERIES 90-97
production.tnemec.comNote: Series 90-97 must be exterior exposed for three days prior to topcoating with Series 1028 or 1029. Note: Series 90-97 must be exterior exposed for one day prior to topcoating with Series 27WB. SURFACE PREPARATION Severe Exposure: SSPC-SP10/NACE 2 Near-White Blast Cleaning with a minimum angular anchor profile of 1.5 mils.
PRODUCT DATA SHEET: EPOXOLINE - SERIES 22
production.tnemec.comCOLORS WH11 Off-White, 1218 Light Blue, 1255 Beige FINISH Semi-Gloss SPECIAL QUALIFICATIONS Series 22-WH11 Off-White, 22-1218 Light Blue and 22-1255 Beige are certified by NSF International in accordance with NSF/ANSI/CAN Std. 61 and the extraction requirements of NSF/ANSI/CAN 600 and are qualified for use on tanks and
PRODUCT DATA SHEET: POTA-POX PLUS - SERIES N140
production.tnemec.comService—After 60 days, scarification or an epoxy tie-coat is required. When topcoating with Series 740 or 750, recoat time ... Read container label warning and Material Safety Data Sheet for important health and safety information prior to the use of …
PRODUCT DATA SHEET: HI-BUILD EPOXOLINE II - SERIES N69
production.tnemec.comCMU Allow mortar to cure for 28 days. Level protrusions and mortar spatter. ... Safety Data Sheet for important health and safety information prior to the use of this product. ... Dense Concrete & Masonry: From 100 to 150 sq ft (9.3 to 13.9 m²) per gallon. CMU: From 75 to 100 sq ft (7.0 to 9.3 m²) per gallon. ...
PRODUCT DATA SHEET: ENDURA-SHIELD - SERIES 73
production.tnemec.comPRODUCT DATA SHEET SERIES 73 PRODUCT PROFILE GENERIC DESCRIPTION Aliphatic Acrylic Polyurethane COMMON USAGE A coating highly resistant to abrasion, wet conditions, corrosive fumes, chemical contact and exterior weathering. Direct-to-Metal capability allows for a labor-saving, high-build, single coat application. NOT FOR IMMERSION SERVICE.
Related documents
Henry Blueskin VP160 Air Barrier System Installation Manual
ca.henry.com3 1. Introduction This installation manual includes materials and installation procedures for Henry® Blueskin® VP160 Self-Adhered Water Resistive Air Barrier system. Blueskin® VP160 meets the current IBC and IECC air barrier requirements for a water resistive barrier (WRB) as referenced in ICC ESR-2975.
PRODUCT DATA SHEET: ENDURA-SHIELD - SERIES 73
production.tnemec.comCMU: Series 1254 Note: Series V530 exterior exposed more than 24 hours, Series L69, N69, V69, 135, L140, N140, or V140 exterior exposed ... consult the latest version of Tnemec Technical Bulletin 13-100 or contact your Tnemec representative. CURING TIME Temperature To Touch To Handle To Recoat 75°F (24°C) 1 hour 5-8 hours 12 hours