U.S. Technical Guide - LP Building Solutions
this technical guide. Please verify availability with the LP SolidStart Engineered Wood Products distributor in your area before specifying these products. LIFETIME LIMITED WARRANTY LP SolidStart Engineered Wood Products are backed by a lifetime limited warranty. Visit LPCorp.com or call 1.888.820.0325 for a copy of the warranty.
Download U.S. Technical Guide - LP Building Solutions
Information
Domain:
Source:
Link to this page:
Documents from same domain
Wall Framing Technical Guide - Engineered Wood Products
lpcorp.comWall Framing Technical Guide 1730F b-1.35E, 2360F b-1.55E and 2500F b-1.75E LSL 2250F ... (prescriptive) and engineered wood-frame wall construction. PRESCRIPTIVE CONSTRUCTION Prescriptive construction provisions for wood-framed walls ... In this guide, the user needs only to select the appropriate ...
LP SolidStart I-Joists Technical Guide for Residential ...
lpcorp.comPlease verify availability with the LP SolidStart Engineered Wood Products distributor in your area prior to specifying these products. LP SolidStart I-Joists Technical Guide for Residential Construction LPI ... Flange Bearing Resistance and that of a wood support will increase with additional bearing length.
Design No. U348 BXUV.U348 Fire-resistance Ratings - ANSI ...
lpcorp.comFire resistance assemblies and products are developed by the design submitter and have been investigated by UL for compliance with applicable requirements. The published information cannot always address every construction nuance encountered in the field. ... density of 0.9 pcf (min R-13 thermal insulation rating), pressure fit in the wall ...
LP SolidStart LSL & LVL Wall Framing Technical Guide
lpcorp.comin direct contact or are used as wall studs spaced no more than 24" oc and properly connected together by an adequate wall sheathing. 7. The allowable Tension, F t, for LP SolidStart LSL is assigned for a standard length of 3 feet. For lengths longer than 3 feet, multiply F
Related documents
Glulam Product Guide - Public.Resource.Org
law.resource.orglumber, the layup designation is identified as a 24F-V4. The “V” indicates that the layup uses visually graded lum-ber. (“E” is used for mechanically graded lumber.) The number “4” further identifies a specific combination of lum-ber used to which a full set of design stresses, such as hori-zontal shear, MOE, etc., are assigned.
LP SolidStart I-Joists Technical Guide for Residential ...
lpcorp.comstrength, stiffness and size than traditional lumber, providing a strong, sturdy floor. We offer longer lengths so that ceilings and floors can be designed with fewer pieces, saving time on installation. Other advantages over lumber include lower moisture content, which makes our I-Joists less likely to split, shrink, twist, warp or bow.
Murphy LVL Technical Design Guide - Murphy Company
murphyplywood.comTested for strength and engineered for quality, Murphy Company LVL represents our ongoing commitment to unsurpassed performance and service. Murphy Company LVL is third-party inspected and audited for quality by APA (The Engineered Wood Association), a leading industry quality assurance organization. General notes for this product guide: 1.
TJI 110, 210, 230, 360, and 560 Joist Specifier's Guide
parr.comEngineered for dimensional stability and predictable performance, Silent Floor® joists resist warping, twisting, and shrinking. The precision engineering that makes Silent Floor® joists strong also makes them easier to install. Silent Floor® joists are designed for easy handling and fast installation. They are lightweight, easy to cut,
CHAPTER 5: Design of Wood Framing - HUD USER
www.huduser.govinstallation. Proper drying and storage of lumber minimizes problems associated with lumber shrinkage and warping. A minimum recommendation calls for using “surface dry” lumber with a maximum 19 percent MC. In uses where shrinkage is critical, specifications may call for “KD-15,” which is kiln-dried lumber with a