UL Evaluation Report - FRTW
6.6 Plywood Diaphragms and Shear Walls: Wood-frame diaphragms are to be designed and constructed in accordance with . of the Section 2306.2. 2018, 2015 and 2012 IBC. Wood-frame shear walls are to be designed and constructed in accordance with . of the Section 2306.3. 2018, 2015 and 2012 IBC. When used, the thickness of PYRO -GUARD ®
Download UL Evaluation Report - FRTW
Information
Domain:
Source:
Link to this page:
Documents from same domain
FSC Mixed Credit - Hoover Treated Wood Products
frtw.comFSC_Mixed_Credit Rev: 5-2012 FSC Chain of Custody (CoC) – Hoover Treated Wood Products Inc. Since January 2007, Hoover Treated Wood Products has maintained a …
HOOVER TREATED WOOD PRODUCTS, INC. - FRTW
frtw.comU301 non-fire side modified U371 non-fire side modified Note: See GA File No. WP 8416 for construction details for fire side. Note: See GA File No. WP 8417 for construction details for fire side
Related documents
SEISMIC LOAD ANALYSIS - Memphis
www.ce.memphis.eduframes or are shear walls. • Diaphragms in one- and two-family residential buildings may be considered FLEXIBLE. • Concrete slab or concrete filled metal deck diaphragms are considered RIGID if the width to depth ratio of the diaphragm is less than 3 and if no horizontal irregularities exist. Diaphragms must be considered as semi-rigid unless
Chapter 12 SEISMIC DESIGN REQUIREMENTS FOR BUILDING …
www.ce.memphis.edusupporting elements, or to slabs designed to act as diaphragms. Where the connection is through a diaphragm, then the member’s ... Ordinary precast shear walls 14.2 and 14.2.3.3 4 21/2 4 NL NP NP NP NP 11. Composite steel and concrete eccentrically braced frames 14.3 8 2 4 NL NL 160 160 100 12. Composite steel and concrete
Seismic Base Shear Determination Steps
www.huntingtonbeachca.gov7. For structures with flexible diaphragms, overhangs beyond the outside line of shear walls or braced frames shall satisfy: a ≤ d/5 8. For buildings with diaphragm that is not flexible, distance between the center of rigidity and center of mass parallel to each principal axis shall not exceed 15% of greatest
STEEL REINFORCEMENT DETAILING - Transport for NSW
roads-waterways.transport.nsw.gov.au2 In bridge decks where cross girders and/or diaphragms are used, the first bars placed will be in the cross girders or diaphragms as these bars must be ... Where interference is of a minor nature only and is not critical e.g. the placing of shear reinforcement, a suitable note to be added to the drawing would be;
STRUCTURAL DESIGN HIGHLIGHTS OF ACI 318-19 PART 2 of …
asceneworleans.orgNov 14, 2019 · section for factored shear in accordance with 7.4.3 and 8.4.3 for one-way shear or 8.4.4.1 for two-way shear shall be measured from the location of the critical section for M u. 13.2.7.3 Circular or regular polygon-shaped concrete columns or pedestals shall be permitted to be treated as square members of equivalent area when locating critical
Calculation of Wind Loads on Structures according to ASCE …
site.iugaza.edu.psIt is the component of the diaphragm which acts primarily to resist shear forced developed in the plane of the diaphragm. Diaphragm Chords: They are components along the diaphragm edges with increased longitudinal and transverse reinforcement, acting primarily to resist tension and compression forces generated by bending in the diaphragm.
Calculation of Wind Loads on Structures according to ASCE …
site.iugaza.edu.psIt is the component of the diaphragm which acts primarily to resist shear forced developed in the plane of the diaphragm. Diaphragm Chords: They are components along the diaphragm edges with increased longitudinal and transverse reinforcement, acting primarily to resist tension and compression forces generated by bending in the diaphragm.
AISI STANDARD - irp-cdn.multiscreensite.com
irp-cdn.multiscreensite.comfor Diaphragms is moved to AISI S310. Section I4, Cold-Formed Steel Light-Frame Construction. The cold-formed steel framing standards are updated. Section I5, Special Bolted Moment Frame Systems. Special bolted moment frame systems should be designed in …