WCD1 - Details for Conventional Wood Frame Construction
the house frame saves little. Such practices may reduce the strength and rigidity of the structure and cause diffi-culty in attachment of cladding materials and trim. Therefore, the details in this document are not intended to be bare minimums; rather, they reflect requirements for producing sound, low maintenance wood frame buildings.
Download WCD1 - Details for Conventional Wood Frame Construction
Information
Domain:
Source:
Link to this page:
Documents from same domain
INTERIOR SHEAR WALLS - awc.org
www.awc.orginterior shear walls to be designed to resist wind loads. WFCM Section 2.4.4.2 states: “Walls parallel to the applicable wind load or seismic motion shall provide the required shear resistance at each level. The sum of the individual shearwall segment shear
2012 ASD/LRFD Manual for Engineered Wood Construction
www.awc.orgASD/LRFD MANUAL FOR ENGINEERED WOOD CONSTRUCTION iii AMERICAN WOOD COUNCIL FOREWORD This Allowable Stress Design/Load and Resistance Factor Design Manual for Engineered Wood Construction (ASD/LRFD Manual) provides guidance for design of most wood-based structural products used in the construction
Prescriptive Residential Wood Deck Construction Guide
www.awc.org4 PRESCRIPTIVE RESIDENTIAL WOOD DECK CONSTRUCTION GUIDE American Wood Council Table 2. Maximum Joist Spans and Overhangs.1 Species Size Joist Spacing (o.c.)
2015 National Design Specification Supplement - awc.org
www.awc.orgAMERICAN WD CUNCIL. DESIGN VALUES FOR WOOD CONSTRUCTION – NDS SUPPLEMENT iii. Introduction. This Supplement is a compendium of reference de …
2005 Span Tables For Joists And Rafters - awc.org
www.awc.org2 EXPLANATION OF TABLES AMERICAN WOOD COUNCIL 7. LUMBER IDENTIFICATION The tabulated spans in these tables apply to lum-ber identified by the grade stamp of, or certificate of
Design Aid 6 Beam Design Formulas with Shear and Moment ...
www.awc.orgAMERICAN WOOD COUNCIL w R V V 2 2 Shear M max Moment x 7-36 A ab c x R 1 R 2 V 1 V 2 Shear a + — R 1 w M max Moment wb 7-36 B Figure 1 Simple Beam–Uniformly Distributed Load
WIND & SEISMIC - AWC
www.awc.org2.1.2.1 Allowable Stress Design: Allowable stress design (ASD) shall be in accordance with the Na-tional Design Specification ® (NDS ®) for Wood Con-struction (ANSI/AF&PA NDS-05) and provisions of this document. 2.1.2.2 Strength Design: Load and resistance factor design (LRFD) of wood structures shall be in accor-
Prescriptive Residential Wood Deck Construction Guide
www.awc.org3. Maximum allowable overhang cannot exceed L/4 or ¼ of actual main span. Assumes cantilever length/180 deflection with 220 lb point load (See Figure 1A and Figure 2). 4. Incising assumed for Douglas Fir-Larch, Hem-Fir, and Spruce-Pine-Fir. 5. Design values based on northern species with no incising assumed. 6. Ledger shall be a minimum of 2x8 ...
2015 National Design Specification - AWC
www.awc.orgNDS-1991 with an approval date of October 16, 1992. In 2010, AWC was separately incorporated, re-chartered, and accredited by ANSI as a standards developing organization. The current edition of the Standard is designated ANSI/AWC NDS-2015 with an approval date of September 30, 2014. In developing the provisions of this Specification,
MAT100: The Basics of Wood Frame Construction
www.awc.orgone comprehensive program for building officials on wood frame construction basics. In each module, learning outcomes will be further refined respectively. MAT 100 learning outcomes (see slide). 5 MAT100: Learning Outcomes 3. Floor, roof/ceiling, wall framing 4. Wall bracing, introduction to Wood Frame Construction Manual 5. Fireblocking ...
Related documents
Full-size Deluxe Murphy Bed Plan
go.rockler.comfull-size bed will extend about 7' into the room when open, and the width of the bed cabinet plus the side cabinets will be about 8' 8". The unit must sit flush against the wall. If the room has base molding, you will need to make relief cuts on the ... Inner Frame Strut Piece ...
Power and Sample Size Determination
pages.stat.wisc.eduSample size calculation Example Consider a population with proportion p. Let X be the number of successes in a random sample of size 100 with model X ˘Binomial(100;p). Consider the hypotheses H 0: p = 0:3 versus H A: p <0:3. The researchers decide to reject the null hypothesis if X 22. 1 Find 2 Find if p = 0:2.
R Reference Card
cran.r-project.orgsample(x, size)resample randomly and without replacement sizeele-ments in the vector x, the option replace = TRUEallows to resample with replacement ... a matrix or a data frame, the variance-covariance matrix is calculated sd(x)standard deviation of x cor(x)correlation matrix of x if it is a matrix or a data frame (1 if x is a
MP-Series Low-inertia Servo Motor with 100 mm to 165 mm ...
literature.rockwellautomation.comFrame Size (IEC 72-1 flange number) 15 = 63 mm small frame motors (63…75 mm) 2 = 75 mm refer to page 24 for this product manual 3 = 100 mm 4 = 115 mm 45 = 130 mm 5 = 165 mm 6 = 215 mm large frame mo tors (215…300 mm) 8 = 265 mm refer to page 24 for this product manual 9 = 300 mm Voltage Class A = 200V B = 400V Series Type L = Low inertia Series
Kinetix TLP Multi-purpose Servo Motors with 046. . . 235 ...
literature.rockwellautomation.comKinetix TLP Multi-purpose Servo Motors with 046…235 mm Frame Size Installation Instructions Catalog Number Explanation (1) Multi-turn revolution depends on the system settings and configuration. (2) Not all combinations are available. Rated power hierarchy is only for comparative purposes.
Sampling and sample size estimation
www.gfmer.chHistory of Sampling (Contd) Dates back to 1920 and started by Literary Digest, a news magazine published in the U.S. between 1890 and 1938. Digest successfully predicted the presidential elections in 1920, 1924,1928, 1932 but; Failed in 1936… The Literary Digest poll in 1936 used a sample of 10 million, drawn from government lists of automobile and telephone