R NDUSTRIAL RECISION & COUPLINGS OMPONENTS

1 DESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: COUPLINGSCLUTCHES, BRAKESB ellows CouplingsZero Adjustable CouplingsFlexible CouplingsMiniature Oldham CouplingsWafer Oldham CouplingsUniversal Lateral CouplingsMulti-Jaw CouplingsPrecision Universal Joint CouplingsMolded Universal Joint CouplingsPrecision Sleeve CouplingsFlexible Zero Backlash CouplingsSpider Coupling1. Clutch2. Power on Brake3. Power off Brake4. Slip Clutch Assembly5. Slip Coupling6. Zero Adjustable Coupling7. Bellows Coupling8. Miniature Oldham Coupling9. Multi-Jaw Coupling10. Flexible Coupling11. Water Spring Coupling12. Universal Lateral Coupling13. Molded Universal Joint14. Precision Universal Joint15. Roller catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: SECTIONI NDUSTRIAL Clutches and Brakes7-2 Bellows CouplingsThe ideal solution where shafts are angularlly andlaterally misaligned. They feature a stainless steel hubpinned to a stainless steel Adjustable CouplingsGet the same characteristics as on the bellows typecoupling, except these COUPLINGS have an adjustablehub for zeroing synchros and other similar Sleeve CouplingsUse them when coupling shafts of similar ordissimilar diameters.

2 This allows you tocouple inch to inch, millimeter to millimeter,and inch to millimeter Zero Backlash CouplingsWork well in high accuracy systems. Stainlesssteel or aluminum one-piece construction withhigh torsional stiffness, constant velocity, andvery low wind K CouplingsAn excellent choice for use in abrasive dustenvironments and where maximum flexibilityis required. The hubs are zinc plated; thebodies are CouplingsThese provide high torque transmissionwithout backlash or vibration due to the use ofa chemically resistant and electrical isolatingelastomer ExtensionsUsed to add an additional inch of shaft lengthor facilitate a change from special to standardshaft diameter. See Section CouplingsThese will isolate vibration, absorb shockloads and electrically insulate. They feature amolded neoprene body connected tostainless steel Oldham CouplingsA choice of center block of oil impregnatedbronze or nylon (eliminates metal-to-metalcontact from taking place) between the these COUPLINGS in Spring CouplingsThe choice for your highest torque applica-tions and where there is up to 8o of angularand.

3 03 inches of lateral Lateral CouplingsNot only will these COUPLINGS provideelectrical insulation, but they can handle upto 10o angular and .05 inches of CouplingsInterlocking teeth permit precision coupling /decoupling with limited transmission errorbetween two stainless steel Joint CouplingsWorking angles up to 30o are no problemwhen you use these coupling . Standard ineither Stainless Steel or SELECTION GUIDEB ellowsX XXXXXX XZero AdjustableX XXXXXX XFlexibleXXXXXXXO ldhamXXXXXW afer SpringXX XXXXXXXXXU niversal LateralXXXXXXXXXM ulti-JawXXXXXXU niversal JointXXXXXXXM oldedUniversal JointXXXXXXXXS leeve CouplingXXXXXX XFlexible ZeroCouplingX XXXXXXXX XFlexible KXXXXXXXXXXS pider CouplingXXXXXXXXC oupling TypeAngular Misalignment > 5oAngular Misalignment < 5oLateral Misalignment > .010"Withstand Shock LoadsVibration DampeningHigh SpeedsHigh TorqueHigh Ambient TemperatureClean Room EnvironmentStepper MotorsReversing DrivesMaintenance RequiredVacuum Environment (No Lube)CompressibilityElectrically InsulatedXDESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: MOUNTED-POWER OFF BRAKES24 VDC and 120 VAC 3/16", 1/4", 5/16", and 3/8" BoresFLANGE MOUNTED-POWER ON BRAKES24 VDC and 90 Volts DC 3/16", 1/4", 5/16", and 3/8" BoresTo Order Alternate Bores and Voltages, Consult FactoryDiagram 1 PICABCDEFGHIJKLD iagramSeriesMax.

4 Nom..500 2 MechanicalHHAir Gap SetAt FactoryElectricalPICABCEFGH I JKLS eriesNom. Max. Nom. Max..001 Max..001 . Out-of-BoxRated StaticTypical Torques AfterTorques 8RX3810 15RX4121520 DESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: MOUNTED-CLUTCHES24 and 90 Volts DC 3/16", 1/4", 5/16", and 3/8" BoresSLIP CLUTCHES CONTINUOUS SLIP OPERATION1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm BoresT17-4, MCH2-4 All Other ModelsDESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: CLUTCHES CONTINUOUS SLIP OPERATIONA djustable TorqueMaximum RPM =WATTS (From Table Below)Torque (oz. - in.) x .0007 Open PlateMaterial:Housing Steel; Zinc PlatedClutch Plates BrassFriction Plates Proprietary (Non Asbestos)Features: A multi plate slip clutch Adjustable torque Preset torque available onspecial orders (Torque setting 10%) Can be used as a slip coupling Backlash of 6o is standard Constant tension Overload protection Controlled slip Clutches exhibit sametorque in either direction Shaft to shaft clutch/ coupling or thru shaft topulley, gear, etc.

5 Bronze bearing in housingfor thru-shaft to pulleymodels Low stick-slip ratioDimensions And Capacity RatingBoreCapacityFrictionABCDE EE No* to to to to to 800 +..005 Capacity at continuous duty, 50 RPM, 25 million cycles (Rev)*Note: For shaft to shaft coupling , set screws in both housingand cartridge use Part No. ending with S For thru shaft to housing (pulley, gear, etc.), bronze bearing inhousing, set screw in cartridge use Part No. ending with H Metric bores can be accomplished by use of bore reducers(5,6,8 & 10 mm finished bores) found in the catalog Consult factory for other bore sizesSLIP COUPLINGS CONTINUOUS SLIP OPERATION1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: coupling & SLIP CLUTCHES ADJUSTABLE-INTERMITTENT DUTY1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm Bores7-6 SLIP CLUTCH ASSEMBLY ADJUSTABLE-MOMENTARY OVERLOAD*Pin Hub 1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm BoresClamp Type 1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm BoresDESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: CLUTCHES Ideal for indexing, backstoppingor overrunning operations Free rolling one way, drives inopposite direction Light weight, low profile High indexing, frequency Temperature max 200 F Maximum Backlash Shaft should be RC58 min.

6 With16 " finish or betterBACKLASH FREE ELASTOMER JAW SPIDER COUPLING1/8" to 1/2" Diameter Bores and 4mm to 12mm BoresFeatures: For electrical isolation and chemical resistance coupling with Integral radial clamp usingsocket head cap screws High torsional stiffness:- Static Lbf-Ft/deg (700Nm/rad)- Dynamic 9 Lbf-Ft/deg (350Nm/rad) Misalignment Tolerances:- Angular - Lateral .002" (.06 mm)- Axial .039" (1 mm) Temp. Range (due to elastomer)22 to 248 F (-30 to 120 C)Specifications: Inch / (Metric) Rated Torque 106 Lbf-in / (12Nm) Over all length " / (26mm) C Fit Length .315" / (8mm) Clamping Screw M3 Torque to tighten screw Lbf-in / (2Nm) Aprox. Weight .07 oz / (.02 kg) Bore Tolerance +.001" / (H7) : Hubs: High Strength Aluminum Elastomer Insert: Precision molded, wearresistant and thermally stable polymer 64 Shore "B1""B2". / boresB1 / boresB1 / B2 PartBoreNumber4T13E-4M5T13E-5M5/4T13E-5M 4M6T13E-6M6/5T13E-6M5M6/4T13E-6M4M8T13E- 8M8/4T13E-8M4M8/5T13E-8M5M8/6T13E-8M6M12 /10T13E-12M10 MMetric BoresMetric to InchB1 / B2 PartBoreNumber4M/.

7 188T13E-4M185M/.188T13E-5M184M/.250T13E- 4M255M/.375T13E-5M376M/.375T13E-6M374M/. 500T13E-4M506M /.500T13E-6M5010M/.500T13E-10M5012M/.500 T13E-12M50 Other bore sizes and combinations available between inch(.188 to .500) and metric (4mm to 12mm) consult catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: SPRING To .50 Inch Bores and 3 To 12 mm BoresMaterial: Hubs and center members Anodized AluminumLeaves 17-7PH Stainless SteelDESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: HubSplit HubSizeScrewNo. (Ref.)Part to 1 # to 1 # #6-32L1-61/8 to 1 #2-56L1-4T1-1T1-81/8 to 3 # #4-40L1-51/8 to 1 # #6-32L1-63/16 to 3 #4-40L1-5T1-2T1-93/16 to 1 # #6-32L1-61/4 to 1 #6-32L1-6T1-3T1-105/16 to 5 #6-32L1-20T1-21T1-233/8 to 3 #8-32L1-21T1-22T1-24 Dimensions below are in to to to to to to to to HubSplit HubSizeScrewNo. (Ref.)Part to 1 #2-56L1-4T9-1T10-11/8 to 3 # #4-40L1-51/8 to 1 # #6-32L1-63/16 to 3 #4-40L1-5T9-2T10-23/16 to 1 # #6-32L1-61/4 to 1 #6-32L1-6T9-3T10-35/16 to 5 #6-32L1-20T9-11T10-113/8 to 3 #8-32L1-21T9-12T10-12 Dimensions below are in to to to to to to to to * Adjustable end is first shaft size turn of adjusting screw rotates coupling hub 12 degrees.

8 Hub and shaft remain fixed during to 3/8" Bore and 3 mm to 10 mm BoresInchBoresToler.+. +. HUBSPLIT HUBZERO ADJUSTABLE COUPLINGS1/8" to 3/8" Bore and 3 mm to 10 mm BoresPIN HUBSPLIT HUBM aterial: Stainless SteelInchBoresToler.+. +. : Stainless 75oz. to Shaft "Angular catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: HubSplit HubSizeScrewNo. (Ref.)Part to 1 # to 3 # # to 1 # #6-32L1-61/8 to 1 #2-56L1-4T11-1T12-11/8 to 3 # #4-40L1-51/8 to 1 # #6-32L1-65/32 to 3 # #4-403/16 to 3 #4-40L1-5T11-2T12-23/16 to 1 # #6-32L1-61/4 to 1 #6-32L1-6T11-3T12-3 Dimensions below are in to to to to to to to 1/4" Bore and 3 mm to 6 mm Bores7-10 PIN HUBInchBoresToler.+. HUBM etricBoresToler.+. LATERAL COUPLINGS1/8", 3/8", and 1/4" Bores and 3, 4, 6 mm angular misalignment: 10oMaximum lateral misalignment:.050 inchesMaximum working torque:15 lb. :NegligibleWeight (1/2" bore):.5 ouncesTrunnion material:Nickel plated metalAnnular ring material:DelrinStandard connection to shaft:Socket head cuppoint set screwFeatures- Simultaneous lateral andangular misalignment- Corrosion resistant- Electrically insulated- Light weight and spacesaving- No lubrication required- SeparableINCHT oleranceBPart &.

9 & .1875T16-2+.001".1250 & . ". & . & . & . &4 MUJ1-23 & 5 MUJ1-7+.025 mm3 & mm4 & 5 MUJ1-84 & 6 MUJ1-55 & 5 MUJ1-95 & 6 MUJ1-106 MUJ1-6 INCH TO METRICT oleranceBPart " & 5 mmT16C4-9+.001".1875" & 6 ".2500" & 3 mmT16C6-1 Metric Bores .2500" & 4 mmT16C6-4+.025 " & 5 " & 6 mmT16C6-6 DESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: COUPLINGS 64 PITCH1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm BoresMINIATURE OLDHAM COUPLINGS1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm Bores48 TEETH - 3/4" TEETH - 17/32" catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: SLEEVE COUPLINGS1/8" to1/2" Bores and 3 to 12 mm BoresPRECISION SLEEVE COUPLINGS1/8" to3/8" Bores and 3 to 12 mm BoresDESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: BACKLASH COUPLING1/8"to5/8"Diameter Bores and 4 mm to 12 mm BoresMisalignment TolerancesBMomentaryBoreLDIntegralDynami cTorsionalParallelAxialPart+.002 Length.

10 016 Dia.. SizeInch Lbs.(Degree/Lb In)(Degree)(Inches)(Inches)..010T22S-62 Dimensions Below are in MillimetersMisalignment TolerancesBBoreLDScrewParallelAxialPart+ .025 .40 .40 (Degree)(Inches)(Inches) ..254MT22S-12 DESIGN catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: FLEXIBLE COUPLINGSBORE REDUCERSInch And MetricMaterial: AluminumInch to inch and inch to metric bore reducers adapt a coupling , clutch, pulleyand other bores to a number of shaft diameters when fitted to a pin hub (setscrew) or split relies on adequate contact area between the shaft and of residual stresses after slitting may result in slight springing of thematerial, this can be corrected by finger optimum fastening install bore reducers as shown: S = Two Set Screw Position C = One Set Screw T = Tangential Screw In Clamp +. +. to Inch ReductionL . 8 (.312) (.433) (.472) (.625) (.625)MR-10-12-12 Part to Metric ReductionL .25(mm)ID+. (mm)OD+. Reducers With Thicker Walls May Have Slot In Opposite Wall For Proper catalog CAD e-commercePhone: 800-243-6125 FAX: 203-758-8271E-Mail: UNIVERSAL JOINTS1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm BoresMOLDED UNIVERSAL JOINTS1/8", 3/16", and 1/4" Bores and 3, 4, 6 mm Bores