Transcription of PKF 255 V8 1.0 BA D/GB/F - Free Instruction Manuals
1 pkf 255 v8 D BetriebsanleitungFormatkreiss ge G Operating InstructionPanel sizing saw F Instructions d'utilisationScie circulaire de format3045150153045 D Die beiliegende Garantiekarte senden Sie bitte an uns zur ck. Den Kaufbeleg bitte aufbewahren! Ein Anspruch auf Garantieleistungenbesteht nur gegen Vorlage des Kaufbelegs. Die Adresse Ihrer n chstgelegenen Werksvertretung finden Sie auf derhinteren Umschlagseite. G Please return the enclosed warranty card to us. Retain proof of purchase! You are only entitled to claim warranty againstproof of see back cover for manufacturer representative s address near-est you.
2 F SVP, retournez-nous la carte de garantie le re u d'achat! La garantie ne peut tre accord e que surpr sentation de ce re trouverez l'adresse de votre repr sentant le plus proche la der-ni re page de couverture. Great pkf 255 v8 Scope of deliveryCarton 1 Panel sizing saw with acces-sories:Carton 2 Travelling sizing table with accessories:3045150153045569111212341387 101 Suction hose for blade guard2 Suction hose for chip case3 Rip fence with auxiliary fence extrusion4 Lock bar5 Connector suction hose / chip case6 Connector for suction hoses7 Hose carrier for suction hose / blade guard8 Push stick / feeding aid9 Blade guard hardware bag10 Travelling sizing table11 Mitre fence (knock-down) with flip stop12 Foot with add-on pieces(only for travelling sizing table 1800 mm)
3 13 Hold-down plate hardware pkf 255 v8 Saw components and controls30451501530458101615112112345761 3141791 Hold-down plate2 Travelling sizing table (1800 mm shown)3 Riving knife4 Suction hose for blade guard5 Hose carrier for suction hose / blade guard6 Blade guard7 Rip fence with auxiliary fence extrusion8 Saw table9 Scribing blade10 Push stick11 Handwheel for depth of cut setting12 Handwheel with lock lever for blade tilt setting13 Workstand (optional accessory)14 Mains connection15On/off switch with emergency stop16 Mitre fence17 Main saw pkf 255 v8 Please read first!
4 Read these instructions before special attention to the safety information. If you notice a transport damage while unpack-ing, notify your supplier immediately. Do notoperate the machine! Dispose of the packing environmentally to a proper collecting point. Keep these instructions for reference on anyissues you may be uncertain about. If you lend or sell this machine be sure to havethe instructions to go with informationSpecified conditions of useThis machine is intended for ripping and crosscut-ting of solid timber, faced board, particle board,wood-core plywood and similar wood-derived not cut round stock without a suitable fixture, asthe rotating saw blade could turn the other use is considered to be not as specifiedand not allowed.
5 Damages caused by unspecifieduse are not covered by the manufacturer's of the machine or use of parts nottested and approved by the equipment manufac-turer can cause unforeseeable safety informationFollow the basic safety requirements for the opera-tion of power tools, to keep the risk of -personal injury-fire-electric shockas little as note in particular:A circular saw is a dangerous tool which can, due tooperator carelessness, cause serious personalinjury. It is therefore recommended you follow thesafety information given below, and know and followthe legal regulations pertaining to the operation ofcircular !
6 The circular saw shall only be started andoperated by persons familiar with circularsaws, and who are at any time aware of thedangers associated with the operation ofsuch under 16 years of age shall use thissaw only under the supervision of an instruc-tor in the course of their vocational following residual risks do principallyexist with circular saws, and can not, even byemploying safety devices, completely elimi-nated: -Risk of injury by touching the revolving sawblade: Keep sufficient distance to the sawblade when sawing.
7 Use push stick if nec-essary. Prevent adverse body positions. Ensurefirm footing, and keep your balance at of injury by touching the saw blade atstandstill: Lower the saw blade after saw-ing until the blade guards rest on the gloves when changing by cluttered work area ( by cut-offs on the floor): Always keep work area of injury by objects being caught dur-ing sawing by the revolving saw blade ( on the saw table or metal parts hid-den in the workpiece): Keep saw table clean. If in doubt checkworkpiece for inclusion of foreign of kickback (workpiece is caught bythe saw blade and thrown against the oper-ator):Always work with a properly set rivingknife.
8 Keep blade sharp and do not generated by environmental influ-ences:Do not operate the circular saw in rain or indamp environment. Ensure sufficient light-ing. Do not operate the circular saw nearinflammable liquids or to other persons in the work area: Keep bystanders, particularly children, outof the danger generated by overloading:Use circular saw within its limits, and onlyas by machine faults:Check the circular saw for damage beforeevery use. Before switching ON check tosee that keys or setting tools are not operate the saw with a damagedON/OFF switch.
9 Keep knobs and handlesfree of oil and pkf 255 v8 Symbols shown on the machineADanger!Disregard of the following warnings can leadto severe personal injury or material not reach into the revolving saw hearing push stick if distancebetween saw blade and rip fenceis 120 round stock only with a suita-ble holding table extension, if otherwiseworkpiece would fall off the tableafter saw blade 250 mmSaw blade arbor bore 30 mmMax. blade speed4000 min-1 Max. depth of cut80 mmSafety devicesRiving knifeThe riving knife prevents the workpiece from beingcaught by the rising teeth of the saw blade andbeing thrown against the operator.
10 Always have riving knife installed during operation. Blade guardThe blade guard protects against accidental contactwith the blade and keeps chips from flying have blade guard installed during stickThe push stick serves as an extension of the righthand and protects against accidental contact withthe saw use push stick if distancerip fence saw blade is 120 mm. In order for the push stick to be always at hand, itcan be stored in a sheath in the machine's housing(arrow).Operating controlsOn/off switch with motor protection To start main saw blade = set rotary switch to ON.
