5-Inch x 8-Inch Horizontal Band Saw

1 Manufactured after Serial no. 946001 Operating Instructions Parts Manual5-Inch x 8-Inch Horizontal band SawModels: 3130/3230 WHM TOOL GROUP2420 Vantage DriveElgin, Illinois 60123 Part No. 9078301Ph.: 800-274-6848 Revision B2 03 WMH Tool GroupThis manual has been prepared for the owner and operators of the Models 3130/3230 Bandsaw. Its purpose,aside from machine operation, is to promote safety using accepted operating and maintenance procedures. Toobtain maximum life and efficiency from your Bandsaw and to aid in using it safely, please read this manualthoroughly and follow the instructions and ServiceWMH Tool Group warrants every product it sells. If one of our tools needs service or repair, one of our AuthorizedRepair Stations located throughout the United States can provide quick service or most cases, a WMH Tool Group Repair Station can assist in authorizing repair work, obtaining parts, orperform routine or major maintenance repair on your Wilton the name of an Authorized Repair Station in your area, please call 1-800-274-6848, or visit our web site InformationRemember, WMH Tool Group is consistently adding new products to the line.

2 For complete, up-to-date productinformation, check with your local WMH Tool Group distributor, or visit our web site at Tool Group WarrantyWMH Tool Group makes every effort to assure that its products meet high quality and durability standards andwarrants to the original retail consumer/purchaser of our products that each product be free from defects inmaterials and workmanship as follows: 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIEDOTHERWISE. This Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligenceor accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, BEGINNINGFROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL.

3 EXCEPT AS STATED HEREIN, ANY IMPLIEDWARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOWLIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOTAPPLY TO YOU. IN NO EVENT SHALL WMH TOOL GROUP BE LIABLE FOR DEATH, INJURIES TO PERSONSOR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISINGFROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOTAPPLY TO take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to anAuthorized Repair Station designated by our office. Proof of purchase date and an explanation of the complaintmust accompany the merchandise.

4 If our inspection discloses a defect, we will either repair or replace theproduct at our discretion, or refund the purchase price if we cannot readily and quickly provide a repair orreplacement. We will return the repaired product or replacement at WMH Tool Group s expense, but if it isdetermined there is no defect, or that the defect resulted from causes not within the scope of WMH Tool Group swarranty, then the user must bear the cost of storing and returning the product. This warranty gives you specificlegal rights; you may also have other rights, which vary from state to WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right to effectat any time, without prior notice, alterations to parts, fittings and accessory equipment, which they may deemnecessary for any reason of ContentsCover 2 Table of Contents.

5 3 General 5-6 Operating 7 Clamping materials in the saw vise .. 7 Right angle 7 Angle 8 Clamping the stock stop .. 9 Blade 9 Change blade 9 Evaluating cutting efficiency .. 10 Cutting the hydraulic feed control .. 10 Blade break-in 10 Change blade 11 Motor guide 11 Maintenance 12 Replacing guide 13 Adjusting back-up bearings .. 13 Adjusting the arm stop adjustment 13 Adjusting motor switch 13 Replacing a back up bearing .. 13 Ajusting the bearing guide seats for blade 14 Test ctting to verify adjustment 14 machine 15 Wiring 15installing coolant 16-17 Replacement 18 Exploded View and Partslist for Lower Saw Head .. 19-20 Exploded View and Partslist for Upper Saw Head .. 21-22 Exploded View and Partslist for Saw Base.

6 23-24 Exploded View and Partslist for Stand & Coolant System .. 25-264 GeneralSpecificationsThe Wilton 5x8 cutoff bandsaw is avail-able as a dry cutting bandsaw or as a wetcutting bandsaw. If required, a dry cuttingbandsaw can be retrofitted with a kit whichconverts it to use with cutting use of a hydraulic feed deliversconsistent accurate cuts and longer blade capacity5 inch (127mm) round7 1/2 inch ( ) wide x 5 inch (127mm) high rectangle8 inch ( ) wide x 1 inch ( ) high flat stock4 1/2 inch ( ) wide x 5 inch (127mm) high at 45 degreesSpeeds85,125,200 SFMB lade driveSteel, heat treated worm driving a bronze worm gear in an oil bathSaw guidesBall bearing mounts on an eccentric shaft, ball bearing rear guidebearings -- all bearings sealed and permanently lubricatedMotor1/2 HP, 115/230V, 1725 RPM capacitor startBlade wheels7-3/8 inch (187mm) diameter flanged cast ironSaw blades1/2 x.

7 025 x 68 inchesFloor model dimensionsWidth 16 inches overall (400mm)Height 38 inches overall with arm Horizontal (950mm)Height 58 inches overall with arm vertical (1450mm)Length - 38 inches (950mm)Optional wet cutting gallon ( ) capacity tank, pump motor: single phase 120V5- Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or Never modify the machine without consulting Wilton - the Stationary Power Tool User - Holdthe Key to and follow these simple rules for best resultsand full benefits from your machine . Used properly,Wilton s machinery is among the best in design andsafety. However, any machine used improperly can berendered inefficient and unsafe. It is absolutelymandatory that those who use our products beproperly trained in how to use them correctly.

8 Theyshould read and understand the Operating Instructionsand Parts Manual as well as all labels affixed to themachine. Failure in following all of these warnings cancause serious General Safety Warnings- Misuse of this machine can cause serious For safety, machine must be set up, used andserviced Read, understand and follow instructions in theOperating Instructions and Parts Manual whichwas shipped with your Setting up machine :- Always avoid using machine in damp or poorlyl ighted work Always be sure the machine support is se- curely anchored to the floor or the work Using machine :- Always wear safety glasses with side shields (See ANSI )- Never wear loose clothing or Never overreach - you may slip and Servicing machine :- Always disconnect the machine from its electri- cal supply while power to the machine must be discon-nected before work is Maintain all machine tools with care.

9 Followall maintenance instructions for lubricating andthe changing of accessories. No attempt shallbe made to modify or have makeshift repairsdone to the machine . This not only voids thewarranty but also renders the machine Machinery must be anchored to the Secure work. Use clamps or a vise to holdwork, when practical. It is safer than usingyour hands and it frees both hands to operatethe Never brush away chips while the machine isin Keep work area clean. Cluttered areas Remove adjusting keys and wrenches beforeturning machine Use the right tool. Don t force a tool or attach-ment to do a job it was not designed Use only recommended accessories andfollow manufacturers instructions pertaining Keep hands in sight and clear of all movingparts and cutting All visitors should be kept at a safe distancefrom the work area.

10 Make the workshop com-pletely safe by using padlocks, masterswitches, or by removing starter Know the tool you are using - its application, limitations, and potential Always wear protective eye wear whenoperatingmachinery. Eye wear shall beimpact resistant, protective safety glasses withside shields which comply with ANSI Use of eye wear which doesnot comply with ANSI result in severe injury from breakage ofeye Wear proper apparel. No loose clothing orjewelry which can get caught in moving soled footwear is recommended forbest Do not overreach. Failure to maintain properworking position can cause you to fall into themachine or cause your clothing to get caughtpulling you into the Keep guards in place and in proper working order.