USB Card Reader (Desktop & MFP) - Inepro - Home

1 2014 Inepro All rights reservedTechnical Manual | USB card Reader (Desktop & MFP)USB card Reader (Desktop & MFP)Product Version: Mk. IIVersion of this manual: card Reader (Desktop & MFP)Congratulations on your selection of Inepro card readers. We are certain you will bepleased with your purchase of one of the flexibele solutions of the want to help you get the best result from your Inepro Back Office Suite. This manualcontains information on how to do that; please read it carefully. Due to continuousproduct improvements this manual is subject to changes without strongly recommend you read the license agreement to fully understand its coverageand your responsibilities of ownership. Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer yourquestions and your wishes, Inepro most versatile card Reader solutionAll rights reserved. No parts of this work may be reproduced in any form or by any means -graphic, electronic, or mechanical, including photocopying, recording, taping, or informationstorage and retrieval systems - without the written permission of the that are referred to in this document may be either trademarks and/or registeredtrademarks of the respective owners.

2 The publisher and the author make no claim to every precaution has been taken in the preparation of this document, the publisher andthe author assume no responsibility for errors or omissions, or for damages resulting from theuse of information contained in this document or from the use of programs and source code thatmay accompany it. In no event shall the publisher and the author be liable for any loss of profitor any other commercial damage caused or alleged to have been caused directly or indirectly bythis created: October 2014 in EditorTechnical EditorsCover DesignInepro de GraafP. BlomK. de GraafProductionInepro CoordinatorR. GroenH. WagenaarR. de KokerUSB card Reader (Desktop & MFP)Table of ContentsIntroduction2 Inepro USB Reader Component List4 Operation8 Software Test10 Hardware Test14 Appendix 117 ATTENTION!!Read this manual carefully before installing the IP Reader !Mains connectionGuarenteeSecurityBefore connecting the appliance to the mains, check that the mains supply voltage correspondsto the voltage printed on the type plate of the adapter.

3 If the mains voltage is different, consultyour guarantee can be given if safety regulations are not disconnect the power supply before handling anything inside the device is in conformity with the EMC directive and low-voltage Conformit Europe ne (Conform European Norm)End of life directivesInepro is paying a lot of attention to environmentally-friendly production. Your new device containmaterials which can be recycled and reused. At the end of its life specialised companies candismantle the discarded device to recycle the reusable materials and to minimise the amount ofmaterials to be disposed of. Please observe the local regulations regarding the disposal ofpackaging materials, exhausted batteries and old device may only be used User OnlyDirectivesVersion - IIIntroductionPartIntroductionVersion - 2 IntroductionThe Inepro USB (Universal Serial Bus) card Reader consists of aUSB interface controller board with a proximity card Reader .

4 Thecontroller board is programmed with software to read out the UID(Unique ID) of the proximity card . By default the card Reader readsout the CSN ( card Serial Number) of the proximity note that the firmware version programmed in the controllerboard is depending on the proximity card technology and, ifneeded, customized read out of the UID of the user a user card is presented to the Reader the host devicereceives the data as a keyboard input in hex Inepro USB card Reader has an unique vendor and aapplication ID. The vendor ID of Inepro = 0x1DA6, the applicationID = 0x0110. For each Inepro USB card Reader the samevendor/application ID is used (regardless of the used Inepro USBcard Reader ). At the connection procedure the software version ofthe Inepro USB card Reader is send to the host Proximity card TechnologiesThe Inepro USB card Reader supports the following proximity cardtechnologies: Mifare ISO 1443A Mifare Desfire ISO 1443A Legic Prime Legic Advant ISO 1443A Legic Advant ISO 15693 USB CommunicationThe Inepro USB card readers supports the USB protocol as aHuman Interface Device (HID).

5 IIInepro USB Reader Component ListPartInepro USB Reader Component ListVersion - 4 Inepro USB card Reader Component ListThe Inepro USB card Reader comes in four version, the desktopand the MFP version in the colours grey and red. The MFP versionis meant to be mounted on the side of an MFP machine, thedesktop version for use on a flat service or installment inside Desktop USB card Reader (Grey) Kit Content 276001 (or Red 276003) 5 - USB card Reader (Desktop & MFP)The Inepro Desktop USB card Reader Kit consist of the USB card Reader Kit-1x Multi ISO Reader Desktop (Grey 276001, Red 276003)-2x Double-sided adhesive tape (for attachment of the USBcontroller to the MFD (Multi Functional Device))-1x Manual Leaflet (P551211)-1x Serial Stickers (P551360)-2x Cable Duct (PS8650) Inepro USB Reader Component ListVersion - 6 Inepro MFP USB card Reader (Grey) Kit Content 276000 (or Red 276002)The Inepro MFP USB card Reader Kit consist of the USB card Reader Kit-1x Multi ISO Reader MFP (Grey 276000, Red 276002)-2x Cable Duct (PS8650)-1x Manual Leaflet (P551211)-1x Serial Stickers (P551360)-1x Bottom Inlay Mounting Cover (Grey PS08818, Red )

6 IIIO perationPartOperationVersion - 8 OperationConnect the readerConnect the Reader to a free USB operation of the Inepro USB readerThe card number that is read by the Inepro USB card Reader is ahex decimal format. This hex decimal number is divided into twoand after that the keyboard representation code of the numbershall be send by the USB interface controller. After the lastcharacter an <enter> keystroke code is software driver that runs in the host will convert the code to theASCII character of the keystroke the card is removed, only a single <enter> keystroke code example: Read value: 0x12345678 (hex decimal number) Send keystroke data:<0x1E> <0x1F> <0x20> <0x21> <0x22> <0x23> <0x24> <0x25> <0x58> Conversion to ASCII characters by the HID host driver:<1> <2> <3> <4> <5> <6> <7> <8> <enter>IVSoftware TestPartSoftware TestVersion - 10 Software TestTesting with the Inepro Test Tool:The Inepro USB card Reader can be tested with a PC or the Reader to the USB port of the PC or the Inepro Test Tool.

7 This will show in the display whichsoftware version is currently used in the Inepro USB card Readerand it will display the card ID when a card is presented to thereader. 11 - USB card Reader (Desktop & MFP)Test with Windows Device a PC or laptop without Inepro Test Tool you can also checkthe version that is in the Inepro USB card Reader . the Inepro USB card Reader to the PC or to Configuration screen -> System -> Device Management-> Human Interface Devices . One of the available HID-USBdevices is the IP card Reader the main page there is a field location and here you will findthe software version of the Inepro USB card Reader . Software TestVersion - 12 Test with the Windows to Inepro USB card Reader to the USB PC or the Calculator application on Windows, set de calculatorunder 'View' in on 'Scientific'. the number system to hex decimal ('Hex'). a card to the Inepro USB card the number system to decimal ('Dec') to read out thedecimal value of this number.

8 This is the card number. VHardware TestPartHardware TestVersion - 14 Hardware TestPhysical test Inepro USB card the top cover of the USB the Inepro USB card Reader to the USB port of the indicator LED's to see if the board is operating as 'sOn the USB interface board are a number of LED s. Each of theLED's has a label, explaining their use. See the table / OKBusyNot OK<undefined> <undefined> <undefined> <undefined> <undefined>ConnectionConnection /transmissionBurns continuouslyBurns continuouslyOffOn / OffOn / PowerBurns continuouslyFlashesOff 15 - USB card Reader (Desktop & MFP)This page has intentionally been left 1 Part 17 - USB card Reader (Desktop & MFP)Appendix 1 Version - 18<This page is intentionally left blank>