Citizen Movement Caliber 6850 - CITIZEN WATCH …

1 Setting Instructions forMovement Caliber 6850 Contents1. Main Components2. Mode Change-Over3. Before Using4. How to Set and Operate Each Mode1. Hand Movement demonstration2. Setting the Time (TME mode)3. Setting the Calendar (CAL mode)4. Setting the Quick-Set Alarm (AL-1 mode)5. Setting the Daily Alarm (AL-2 mode)6. Stopwatch Operation (CHR mode)7. Setting the Timer (TMR mode)8. Setting the Local Time ( L-TM mode)9. Monitoring in the Normal Time Mode10. All-Reset Function11. Calculation Operations5. of Your Timepiece.(click on a topic) 1 MAIN COMPONENTS2 MODE CHANGE-OVERPush the (M)(lower right) button in the normal position to switch betweenmodes as shownNote:Always check the mode hand to ensure the WATCH is set in the desired mode duringuse, since pressing the (M)(lower right) button unknowingly during operation mayoccurReturn to Table of ContentsReturn to Table of Contents3.

2 BEFORE USEB efore use, follow the procedures below to ensure that all WATCH components arein proper working order:Confirm the Zero position setting:ZERO POSITION SETTINGxAll hands, except the modehand, move to the 0 positionxThe 24-hour hand issynchronized with thehour/minute handsEach hand positioned as listed below confirms the 0 position setting is correct:Hour Hand0 hourMinute Hand0 MinutesSecond Hand0 Seconds24-Hour Hand0 hourAuxiliary Hand0 minutesIf the WATCH hands are not positioned as above,follow the Zero Position Setting procedures toensure proper Pull the (M) button out to the first steppositionPush the (A) button to set the second handto the 0 second positionPush the (B) button to set the Auxiliaryfeature hand to the 0 hour positionPush the (C) button to set the hour, minuteand 24-hour hands to the 0 hour, 0 minuteposition2.

3 Be sure to push the (M) button in to itsnormal position. This completes the ZeroPosition SettingPress and hold down the (A), (B), or (C)buttons to activate the quick-advancefeatureA strong shock may cause the hands to moveReturn to Table of ContentsReturn to Table of Contents4. HOW TO SET AND OPERATE EACH MODE1. HAND Movement DEMONSTRATIONP ushing of the (A), (B) and (C)button at once will cause thesecond, minute and auxiliaryfeature hands to stop in the 0 position after moving through thefollowing Hand: (1)+5min ->(2) 10min -> (3) +5minSecond Hand: (1)+5sec ->(2) 10sec -> (3) +5secAux. Hand. : (1)+5 ->(2) 10 -> (3) +5 Return to Table of ContentsReturn to Table of THE TIMEC hanging the time from 10:10:15 to 19:20:00xThe hour/minute hand is based on the 12-hour clock system.

4 Use the 24-hourhands as a reference under normal time setting procedures to determinemorning or afternoon timesSetting Procedures<(M) button in the normal position>Resetting the second handxPressing the (A) button while thesecond hand is between 0-29 secondswill not alter the minute handpositionxPressing the (A) button while thesecond hand is between the 30-59seconds position will advance theminute hand to the next full minutepositionReturn to Table of ContentsReturn to Table of ContentsPush the (M) button in to the normal position3. SETTING THE CALENDAR (CAL) Changing the calendar from May 5 to Sept. 9. Press and hold down either the (B) and (C)buttons to use the quick-advance feature Quick-advance function: Hand Movement is abouttwice as fast after the first revolution.

5 (clockwise Movement only) The hour/minute/24-hour hands are synchronizedAutomatic Calendar SystemThe calendar feature on this WATCH requiresno adjustment at the end of the for Feb 29 during a leap year<(M) button normal position)(May 5)Return to Table of ContentsReturn to Table of ContentsSetting Procedures Press and hold down either the (A) or (B) button for the quick-advance feature. The month and date must be independently set.<Press the (M) button in to the normal position>Automatic Calendar Correction SystemWhen a non-existent date is entered, thewatch will automatically set the date tothe 1st of the following month when the (M)button is pushed in to the normal : Feb 30 -> March 1stReturn to Table of ContentsReturn to Table of Contents4.

6 SETTING THE QUICK-SET ALARM (AL-1)Alarm can be set in this position (M) button in normal positionQuick-Set Alarm FunctionWhen the alarm is OFF hands displaythe current time. This feature allowsthe alarm to be easily set to thedesired time within the 23 hour 59minute maximum limit. Following onering of the alarm (10 seconds) thealarm setting is automaticallycleared from memory and the auxiliarytime display returns to the currentset time.<Sound monitor>(5 seconds)Return to Table of ContentsReturn to Table of ContentsSetting Procedures<hour/minute settings>Clockwise<hour/minute settings>Counterclockwise<Quick-set alarm auto ONfunction>Alarm ON: second hand stops in the 0 positionAlarm OFF: hands displaythe current time Press and hold down either the (B) or (C)button for the quick-advance setting feature Quick-advance function: Hand Movement isabout twice as fast after the firstrevolution (clockwise Movement only) The hour/minute/24-hour hands aresynchronizedAfter adjusting thehour and minutes, thesecond hand returnsto the 0 positionand stops.

7 The alarmis now ON.<Alarm quick-set is complete>(20:10)<Canceling the quick-set alarm>xPress the (A) button aftersetting the quick-set alarm andthe hour/minute/scond/24-hourhands will display the currenttime. The quick-set alarm will beturned OFF>Return to Table of ContentsReturn to Table of Contents5. SETTING THE DAILY ALARM Setting the alarm to ring every day at 15:00 (3:00 pm)Setting ProceduresxDaily Alarm FunctionAfter the alarm time has been setonce, the alarm will sound everydayat the same time for 15 secondsxAlarm Sound SwitchThe switch allows you to choosebetween 2 levels of sound (loud orsoft) for the alarm<(M) button normal position> <Sound monitor>(8 seconds)<(M) button pulled out to 1st step position> <Hour/Minute setting> <Hour/Minute setting> Press and hold down eitherthe (B) or (C) button touse the quick-advancefeature Quick-advance function.

8 Hour and minute handmovement is about twice asfast after the firstrevolution (clockwisemovement only) Use the 24-hour system toensure morning andafternoon, (am/pm), are to Table of ContentsReturn to Table of ContentsDaily alarm auto ONDaily alarm sound selectorxPull the (M button out to the first step position (one click out). Thesecond hand moves to position (2) and the alarm is turned the (A) button to switch between a softer or louder sound level. )thelevel of the alarm sound in position (3) is softer than position (2)) or toswitch alarm OFF (position 1)<Push the (M) button in to the normal position>Alarm setting is completeReturn to Table of ContentsReturn to Table of Contents6.

9 STOPWATCH OPERATION (CHR)1/20 second Display (effective only timings exceeding 1 minute)xMax. stopwatch range: 60 minutes in1/20 second intervalsThe auxiliary hand displays in 1/20second incrementsxStarting from the stopwatch resetstate, the auxiliary hand advances for1 number of elapsed minutesexceeding 1 minute are hour/minute/24-hour hands displaythe current time in the seconddisplays onlywhile the (B)button is helddownxRelease the (B)button to displaythe number ofelapsed minuteswith the to Table of ContentsReturn to Table of Contents7. SETTING THE TIMES etting the timer to10 minutes<Timer setting procedures> (M) button normal positionxMax. timer range 60 minutes in 1minute incrementsxFly-back function: This featureallows you to press the (C) buttonafter the timer countdown hasstarted to return to the beginningof the timer setting andautomatically start the countdownover againxThe handsdisplay the current set time inthe timer settings are madewith the auxiliary handxAuxiliary hand (timerminutes)xSecond hand (timerseconds)Countdown proceeds at thesame time(returns to timer startposition) A confirmation beep sounds with each start, stop, reset and fly-back operation Press and hold down the (B) button to use the quick-advance feature while settingthe timerReturn to Table of ContentsReturn to Table of Contents8.

10 SETTING THE LOCAL TIME (L-TME) Changing the local time from 10:20 to 15:20 (3:20 )Local time is the time in the current trips, the dual time feature can be used bysetting the WATCH to the local Procedures <(M) button normal position> <(M) button: 1st step position> <Hour/minute setting> <Hour/minute setting>xPress and hold down either the (B) or (C) button to use the quick-advancefeaturexHour/minute/24-hour hands are synchronizedxMinute hand is adjustable in 30-minute increments only. Second hand is to Table of ContentsReturn to Table of Contents<Push the (M) button in to the normal position>Local time setting is complete at 15:20 (3:20 )9.