Transcription of TITAN Geotechnical System - ischebecknz.co.nz
1 GEOTECHNICTITAN Geotechnical SystemDirect drilled and continuous flush grouted anchors,micropiles and soil nails Technical data Drill bit types Grout body diameters2 Anchor / Pile TypeUnitTITAN30/16 TITAN30/14 TITAN30/11 TITAN40/20 TITAN40/16 TITAN52/26 TITAN73/56 TITAN73/53 TITAN73/45 TITAN73/35 TITAN103/78 TITAN103/51 TITAN127/103 Nominal Outside Diameter mm30303040405273737373103103127 Nominal Inside Diameter mm161411201626565345357851103 Effective Cross Section Aeffmm 3403754157309001250136016152239271431405 6803475 Ultimate Load FukN245275320540660925103511601575186522 70366023202)Yield Point F0,2,kkN19022026042552573083097012701430 180026702030 Yield Stress f0,2,kN/mm 560585625590590585610590560530565470585 Axial rigidity E x A 1)10 kN6369831351672312512994145025801022640 Flexural rigidity E x I 1)106kNmm 3,73,85,21517421251431781855647941163 Weight ,72,873,295,67,179,8710,7513,217,821,225 ,344,628,9 Standard lengthm33/42/3/43/42/3/436,25334333 Thread Left / Right Hand-leftleftleftleftleftleft/rightright rightrightrightrightrightright1) The values are based on test results, it is not possible to evaluate an E-modulus out of these values.
2 E. & subject to change without notice 2) Only valid for the hollow bar without coupling nut, the ultimate load of the coupling nut is 2048 kNTechnical data3 Drill bit typesdrill bits mmhardenedclay bitcross cutdrill bitbuttondrill bitcarbide crosscut/tri-wing drill bitcarbide buttondrill bitcarbide crosscut 3-step drill bitdescriptionfor clay, soft soil and sand/gravel< 50 mixed soil withobstacles> 50 weathered softrock and gravelhardness < 70 MPa for hard rock granite, dolomite,sandstone, hardness70-150 MPafor very hard or highquartzite rockhardness > 70 MPafor directional stability of 2 % of the total lengthTITAN 30/..with adaptor 40 7595110150769011542465155704670905170907 590 TITAN 40/..with adaptor 5211015017590115130707090709011590 TITAN 52/..130175115130----115-- TITAN 52/..with adaptor 73130175200115130175--115130115130130 TITAN 73/..with adaptor 103200220280130175--130175130175130 TITAN 103/..220280175--175175-- TITAN 127/..220200----200--* Illustrations are subject to alterations30/.
3 30/.. 40/..40/.. 40/.. 52/.. 73/..103/..40/..52/.. 73/..103/.. right hand left handanchor/pile typedrill bit diameter mmrock mmcohe-sive soilmmsand andgravel-sandmmmedium andcoarse gravelmmTITAN 30/..button drill bit4252 TITAN 30/..button drill bit4656 TITAN 30/..button drill bit5161 TITAN 30/..button drill bit5565 TITAN 30/..carbide cross cut drill bit4656 TITAN 30/..carbide button drill bit5161 TITAN 30/..carbide cross cut 2-step drill bit7585 TITAN 30/..cross cut drill bit76100125150 TITAN 30/..cross cut drill bit90115140165 TITAN 30/..hardened clay bit75100125150 TITAN 30/..hardened clay bit95120145170 TITAN 30/..piling cone75100 TITAN 40/..hardened clay bit110135160185 TITAN 40/..hardened clay bit150175200225 TITAN 40/..button drill bit7080 TITAN 40/..carbide button drill bit7080 TITAN 40/..carbide button drill bit90100 TITAN 40/..carbide cross cut drill bit7080 TITAN 40/..carbide cross cut drill bit90100 TITAN 40/..cross cut drill bit90115140165 TITAN 40/.
4 Cross cut drill bit115140165190 TITAN 40/..carbide cross cut 3-step drill bit90100 TITAN 40/..piling cone90115 TITAN 52/..cross cut drill bit115140165190 TITAN 52/..cross cut drill bit130155180205 TITAN 52/..hardened clay bit130155180205 TITAN 52/..hardened clay bit175200225250 TITAN 52/..carbide cross cut drill bit115125 TITAN 52/..carbide button drill bit115125 TITAN 73/..cross cut drill bit130155180205 TITAN 73/..cross cut drill bit175200225250 TITAN 73/..carbide tri-wing drill bit130140 TITAN 73/..hardened clay bit200225250275 TITAN 73/..carbide button drill bit130140 TITAN 73/..carbide cross cut 3-step drill bit130140 TITAN 103/..hardened clay bit220245270295 TITAN 103/..hardened clay bit280305330355 TITAN 103/..cross cut drill bit175200225250 TITAN 103/..carbide button drill bit175185 TITAN 103/..carbide tri-wing drill bit175185 TITAN 127/..cross cut drill bit200225250275 TITAN 127/..hardened clay bit220245270295 TITAN 127/..carbide button drill bit200210 Indicative grout body diametersW br Errors and modifications excepted!
5 ISCHEBECK 2010 MegashoreHV-SystemSlabforming SystemsWallformPropsBeam FormsColumn FormsFormwork TiesRail PostsStrutsTrenching SystemsGeotechnicalSystems.. technically advanced formwork, shoring, trenching and Geotechnical systemsCERTIFIED QUALITY SYSTEMDIN EN ISO 9001 / 2000 Zertifiziert durch DVS ZERT e. DE-96-010 DIN EN ISO 9001 FRIEDR. ISCHEBECK GMBH Box 13 41 DE-58242 ENNEPETAL GERMANY + 49 - 2333 - 8305-0 FAX + 49 - 2333 - 8305-55 E-MAIL: INTERNET: office Ennepetal register court Hagen HRB 5585 VAT : DE811161225 joint managing directors: Ernst Friedrich Ischebeck, Friedrich D pp, Dipl. Bj rn Ischebeck
