Operator’s Manual

1 IDPINFINITY D Process MeterOperator s Manual NEWPORTE lectronics, MetersPID ControllersClock/TimersPrintersProcess MetersOn/OffControllersRecordersRelative HumidityTransmittersThermocouplesThermis torsWireRate MetersTimersTotalizersStrain GaugeMetersVoltmetersMultimetersSolderin g IronTesterspH penspH ControllerspH ElectrodesRTDsThermowellsFlow SensorsFor Immediate AssistanceIn the and Canada: 1-800-NEWPORT In Mexico: (95) 800-NEWPORTSMOr call your local products fromNEWPORTnetSMOn-Line NEWPORTE lectronics, is the policy of NEWPORT to comply with all worldwide safety and EMC/EMI regulations that constantly pursuing certification of its products to the European New Approach add the CE mark to every appropriate device upon information contained in this document is believed to be correct but NEWPORTE lectronics, Inc.

2 Accepts no liability forany errors it contains, and reserves the right to alter specifications without : These products are not designed for use in, and should not be used for, patient connected NOTICE:The Meter Case Bezel Design is a trademark of NEWPORTE lectronics, Inc., registered in the This product is covered by one or more of the following patents: Pat. No. Des. 336,895; 5,274,577 / CANADA2052599; 2052600 / ITALY1249456; 1250938 / FRANCE BREVETNo. 91 12756 / SPAIN 2039150; 2048066 / UK PATENTNo. GB2 249 837; GB2 248 954 / GERMANYDE 41 34398 C2. OTHER INTERNATIONALPATENTS device is marked with the international caution symbol.

3 It is important to read the SetupGuide before installing orcommissioning this device as it contains important information relating to safety and OBJECTIVESThis Manual shows you how to set up and use the Programmable Process , WARNINGS and CAUTIONSI nformation that is especially important to note is identified by three labels: NOTE WARNING CAUTION IMPORTANTNOTE: provides you with information that is important to successfullysetup and use of the Process or WARNING: tells you about the risk of electric , WARNING or IMPORTANT: tells you of circumstancesor practices that can effect the meter's functionality and must refer toaccompanying of ContentsSectionPageSEC 1 INTRODUCTION.

4 Unpacking .. Safety Considerations .. 2 SEC 2 ABOUT THE METER.. Front of the Meter .. Back of the Meter .. Disassembly.. 6 SEC 3 GETTING STARTED.. Changing Configuration Jumpers.. 73. 2 Mounting the Meter .. Connecting Sensor Input .. Connecting Main Power.. 12 SEC 4 CONFIGURING THE METER.. Selecting the Input Range .. 134. 2 Selecting a Decimal Point Position.. Scaling the Meter.. Internal Scaling .. 2 Live Scaling .. Changing the Meter s Calibration.. 17 APPENDICESAC hecking and Changing Main Board Power Jumpers .. 19 BReference Tables .. 21 CSpecifications.

5 23 DCE Information .. 25iiList of FiguresFiguresPage2-1 Front-Panel ..32-2 Connectors (ac-Powered and dc-Powered) ..52-3 dc-Power Connections ..63-1 S1 - S4 Jumpers ..83- 2 Meter - Exploded View ..83-3 Panel Cut-Out ..93-4 3-Wire dc Voltage Input Connectionswith Internal Excitation ..93-5 2-Wire dc Voltage Input Connectionswith External Excitation ..103-6 4-20 mA Input Connections with External Excitation ..103-7 4-20 mA Transmitter Hook-Up with Internal Excitation ..113-8 dc Current Input Connections with Current Source ..113-9 Main Power Connections ac .. 123-10 Main Power Connections dc.

6 12A-1 115 Vac Jumper Wiring (default) ..19A-2 230 Vac Jumper Wiring ..20C-1 Meter Dimensions ..24 List of Tables TablePage2-1 Connector Description.. 53-1 S1 - S4 DIP Switches .. 73- 2ac Power Connections .. 1 24-1 Meter Calibration Table .. 18B-1 Display Messages .. 21B- 2 Menu Configuration Displays .. 21B-3 Run Mode Displays .. 22B-4 Factory Preset Values.. 22 iiiNOTESivSECTION 1. UNPACKINGR emove the Packing List and verify that you have received all equipment. Ifthere are any questions about the shipment, use the phone numbers listed on theback cover to contact the Customer Service Department nearest receipt of shipment, inspect the container and equipment for any signs ofdamage.

7 Note any evidence of rough handling in transit. Immediately report anydamage to the shipping carrier will not honor any claims unless all shipping material issaved for their examination. After examining and removing contents,save packing material and carton in the event reshipment is that you receive the following items in the shipping box:QTYDESCRIPTION1 Programmable indicator/controller with all applicable s Manual1 Quick Start ManualIf you ordered any of the available options (except the BL blank Lensoption), they will be shipped in a separate container to avoid anydamage to your SAFETY CONSIDERATIONSThis device is marked with the international caution symbol.

8 It is important to readthis Manual before installing or commissioning this device as it containsimportant information relating to Safety and EMC(Electromagnetic Compatibility).This instrument is a panel mountdevice protected in accordance with EN 61010-1:2001, electrical safety requirements for electrical equipment for measurement, con-trol and laboratory. Installation of this instrument should be done by qualified person-nel. In order to ensure safe operation, the following instructions should be instrument has no power-on switch. An external switch or circuit-breakershallbe included in the building installation as a disconnecting device.

9 It shall be marked toindicate this function, and it shall be in close proximity to the equipment within easyreach of the operator . The switch or circuit-breaker shall not interrupt the ProtectiveConductor (Earth wire), and it shall meet the relevant requirements of IEC 947 1 andIEC 947-3 (International Electrotechnical Commission). The switch shall not be incor-porated in the main supply , to provide protection against excessive energybeing drawn from themain supply in case of a fault in the equipment, an overcurrentprotection device shallbe installed. Do not exceed voltage rating on the label located on the top of the instrumenthousing.

10 Always disconnect power before changing signal and power connections. Do not use this instrument on a work bench without its case for safety reasons. Do not operate this instrument in flammable or explosive atmospheres. Do not expose this instrument to rain or moisture. Unit mounting should allow for adequate ventilation to ensure instrument does notexceed operating temperature rating. Use electrical wires with adequate size to handle mechanical strain and powerrequirements. Install without exposing bare wire outside the connector to minimizeelectrical shock Considerations Whenever EMC is an issue, always use shielded cables.