CNC-330 Series

1 CNC-330 Series Technical manual VER. TAILY AUTOMATION ! 1. INTRODUCTION ..2 2. INSTALLATION AND WIRING ..3 3. CONTROL PANEL 4. CONFIGURATION SETTING & ADJUSTMENT ..8 5. DATA TRANSMIT .. 11 6. SOFTWARE UPDATE ..12 7. MAINTAIN AND TROUBLESHOOTING ..13 8. SPECIFICATIONS ..15 2 CNC-330 Series Technical manual!!VER. TAILY AUTOMATION 1. Introduction Thanks on your purchase of TAILY AUTOMATION CNC-330 Series of micro controller. The CNC-330 is a high-performance micro controller, manufactured using high-quality component and the latest single chip microprocessor.

2 This manual will help in the installation, parameter setting, operate and daily maintenance of the CNC-330 controller. To guarantee safe installation and operation of the equipment, this manual should be read and understood before the actual installation begins. Some of software edition the CNC-330 used, with different functions and wiring diagrams, please consult each software editions users manual for the details. Model CNC-330 Series offers two different models, depending on whether a close-loop driver is provided for various applications. AC Power input offers AC100V~120V and AC220V~240V, 50/60HZ. Model Winding spindle Guiding traverse CNC-330S Drive DC motor in directly Drive 2 phase step motor in directlyCNC-330E External connect winding spindle motor driver Drive 2 phase step motor in directly or external connect guiding traverse motor driver Caution The controller should be operated in an environment that is protected from moisture, corrosive gases, oil-mist, and airborne dust, metallic particles.

3 The controller should be operated free from magnetic noise, if not, use a noise filter to minimize of electromagnetic interference. Normally operate under 5 ~40 environment, do not block the intake/exhaust ports of the controller. Otherwise, a fault may occur. Do not connect or disconnect connectors while power is applied to the controller. There are highly sensitive components on the printer circuit boards. To avoid damage to these components, do not touch these components or the circuit boards with your bare hands or using other metal objects. Make sure all the connectors are connected to the correct position before turn on the power.

4 Make sure that the power source supplies the correct voltage and is capable of supplying the required current to the controllers. Make sure that the machine and controller are properly grounded. CNC-330 Series Technical manual!!VER. 3 TAILY AUTOMATION ! 2. Installation and wiring Accessories (option) All accessories are optional to order. Counting discWinding spindle Counting sensorHome sensor Guiding traverse Winding spindle (90cm)STEP motor connection cable Guiding traverse*CNC-330E use only(90cm)control signal output cable Guiding traverse*CNC-330E use only(90cm)control signal output cable Winding spindle DC motor connection cable Name / (length)Outline drawingModel330-CN2330-CN3330-CN4330-CN5 330-CN6330-CN7330-CN8S330-CN8E330-CN9330 -CN10330-CN11 HMS-01 ACTS-03 ACOUNTINGDISCRS-485 Connection box(80cm)Home sensor connection cable(90cm)Counting sensor connection cable(90cm)Operate switches connection cable(90cm)Aux.

5 Input/Output connection cable(90cm)AC power connection cable(90cm)Winding spindle (90cm)Brake connection cable(90cm)*CNC-330S use only 4 CNC-330 Series Technical manual!!VER. TAILY AUTOMATION Dimensions (unit=mm) x / 71 Counting CNC-330 Series Technical manual!!VER. 5 TAILY AUTOMATION ! Counting system assembly (unit=mm) The counting disc and the sensor must assembly as below, otherwise it will count improperly. sensorZeroing discCounting sensor 71 71 x We have not supplied Zeroing disc, If zero point is necessary for the winding spindle, please made a zeroing disc by oneself and coupling it with counting disc.

6 Home sensor assembly (unit=mm) The home sensor and the interrupter must be assembly as below, otherwise a fault may occur. sensorMax. 6 CNC-330 Series Technical manual!!VER. TAILY AUTOMATION I/O signal Interface description F-OUTV-OUTNameCNC-330 interface circuitExternal deviceHOMESTARTPHA,PHB, +24V+24V+24V+24V+24V+15V+15V+15V+5V+5V10 0 ROP1~OP4OP21~OP28 LAMP1 LAMP2 LAMP356 RBRAKERUN(CW)F/R(CCW)H/LPUS1~PUS3 DIR1~DIR3 PHA2,PHB2,PHC2 COMDC0~10 VBK+BK-Lamp-+24 VOutputInputCOM+OUT-SensorSwitchLoad-+DC 24 VDC24V100mA MAX50mA MAXDC24V+LampBrakeDC24V500mA MAXF-OUTV-OUTCOMV+Winding spindle motor driverSpeed Motor driverV+PUS,DIRRUN,F/R,H/LRRIP1~IP4,IP21 ~IP28+24V CNC-330 Series Technical manual!

7 !VER. 7 TAILY AUTOMATION ! 3. Control panel description COPYSENDSELO peration & Setting keyCNC-330 STATUS IndicatorsOPTIONS SelectionOperation keyDATA IndicatorsSTEP ControllerSETENTDELINSNEW Status indicators Indicates operation status. Indicator On Off Flash READY Ready Run/Edit Pause RUN Run Ready/Edit AUTO Automatic mode Manual mode Data linking Data indicators Indicates data items at data display Indicator (on) Edit mode Operation mode POS Starting position of guiding traverse Position WIDTH Separating region of guiding traverse PITCH Separating pitch TURNS Total number of turns Turns SLOW Number of turns to be winding at low speed before finish SPEED Rotating speed of winding spindle RPM(speed)

8 OPTION Running Options Winding direction Guiding direction Auto starting Auto positioning Edge stop DEG No function in standard edition FUN I/O Function (All Indicators off) Production quantity STEP display Displays STEP number, function code, item number. DATA display Displays file name, winding data, position, turns, RPM(speed), quantity. Options selection Indicate numerical key for options select. 8 CNC-330 Series Technical manual!!VER. TAILY AUTOMATION 4.

9 Configuration setting & adjustment Configuration setting When supplied the power to CNC-330 for the first time after finish installation, the configuration set is necessary to insure CNC-330 is meet various winding machines specification request. In READY mode, press SET SEL 0 to invokes this function, STEP Display shows item number[ ], DATA display shows setting value [ XXXX ], If no change is necessary, press ENT going to next item, or press , then the parameter can be modified by pressing numerical key followed by ENT , There are 9 items can be set in this function at most(some software edition less then 9 item), Press SET again to finish this function.

10 In this function press to select item number, press CLR to clear setting value. When item number [ ],[ ],[. ] setting value as [ 0 ] means without that function. SET SEL 0 Configuration setting Item Function Setting range Description Station number 1~9999 This station number used to identify the station when using RS-485 communication function, (Initial value as 1). Password 0000~9999 If password has been set, when press SET or SEL keys, the controller will request to key-in four digits of password, if passed, you can edit the setting data according normal procedure until turn off power or press RESET , if not, you can not edit any setting data, (initial value as 0000).