Die Reparatur von Konica Minolta 2430DL Toner …

1 Repairing Konica Minolta 2430DL TonerDetection ErrorRepairing Konica Minolta 2430DL Toner Detection ErrorGeschrieben von: HoyeBoyeEINLEITUNGP rinter will present error stating the Toner cartridges are not installed when Toner cartridges AREinstalled. This guide will walk you through repairing and replacing the Toner cartridge Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 1 von 9 Schritt 1 Repairing Konica Minolta 2430DL Toner Detection ErrorPower down and unplug printer before performing the following instructions. Open top lid by pulling up on gray handle and lifting the cover open. Pull down front cover by pulling horizontally, away from the printer, on the center of the cover. Schritt 2 Lift the Toner handle away from thetoner until you hear a "pop" and feelthe cartridge disengage from thecartridge holder.

2 Lift the up by the handle; it will pivotaround the top edge of the cartridgeholder. Continue lifting until tonerstops pivoting. You can now lift the Toner straightup, out of the cartridge holder. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 2 von 9 Schritt 3 You will need to rotate the cartridgeholder to remove the remainingcartridges. Insert a thin rod into the "barrel"shaped hold on the right side of theprinter. This will disengage thecartridge holder lock. You will needto press and hold to keep the lockdisengaged. Press down on the empty cartridgeslot. The carousel will begin torotate. Rotate the carousel until thecartridge pivot tabs line up the thealignment opening. Repeat steps 2 and 3 until all tonercartridges are removed.

3 Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 3 von 9 Schritt 4 The drum is light sensitive. Do notperform this procedure in directsunlight. Lift up on the green drum handle. Continue lifting until the drum iscompletely removed from the printerhousing. Place the drum on a flat surface withthe drum roller covered orunexposed to light. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 4 von 9 Schritt 5 The sensor is located in the lower right hand corner of the printer. It is housed in a spring-loadedholder on a pivot. Press the holder down so the spring is compressed. Use a long and narrow rod (screwdriver) topull one side of the pivot axle out of the axle housing.

4 The sensor and housing can now be removed from the printer. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 5 von 9 Schritt 6 Remove the sensor from thehousing by releasing the tensionclips on the back of the housing. If you have purchased a newsensor, skip to step 10. Continue to step 7 for instruction onrepairing the sensor. Schritt 7 FRAGILE COMPONENT. Proceedwith caution. Use a tiny screwdriver to pry openthe top edges of the sensor. Pry open the bottom edges of thesensor. The senor will come apart in5 pieces. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 6 von 9 Schritt 8 Spray all surfaces with electronics contact cleaner, including conductor pads, spring conductors,and cable connectors.

5 Wipe clean with paper towel. You may need to scrub the conductor padsroughly. Ensure spring conductors are all properly shaped (not folded in on itself) Schritt 9 Place the spring conductors back in the sensor lid with a pair of tweezers as shown. Place the main sensor body into the sensor lid and snap the sensor closed. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 7 von 9 Schritt 10 Hold the sensor housing spring onto the sensor housing spring post. Install the white sensor housing back in the printer, holding the spring in place. Schritt 11 Hold the sensor cable in place with a pair of tweezers or clips. Connect the sensor to the sensor cable. Press the sensor into the white sensor housing. MAKE SURE BOTH SPRING CLIPS SNAP INPLACE.

6 Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 8 von 9To reassemble your device, follow these instructions in reverse 12 Clean all contacts on each Toner cartridge with contact cleaner and a paper towel. Install printer drum. Install each Toner cartridge, following steps 2 and 3 in reverse. Apply power to the printer. Your printer should operate with no errors. Repairing Konica Minolta 2430DL Toner : 2016-03-16 Anleitung Nr: 14301 -Dieses Dokument wurde am 2021-02-09 06:43:09 PM (MST) erstellt. iFixit CC 9 von 9